Atur jumlah dan catatan
Stok Total: 137
Subtotal
Rp3.086.000
New Assembled ATU-130 1.8-50MHz 150W Automatic Antenna Tuner OLED Display Meatl Case Update of ATU-100
Rp3.086.000
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: Semua Etalase
ATU-130 is used as a part of amateur radio equipment amplifier or transceiver, or as a separate device that performs the function of matching the output impedance of the power amplifier (PA) with the antenna feeder. This device contains a set of 7 inductors and 7 capacitors, which can effectively cover the wideband radio amateur shortwave range from 1.8 MHz to 50 MHz.
Parameter
Supply voltage range: 10-15 VDC(center is +)
Maximum working power: 150 watts
Minimum power required to start tuning: 5W
Minimum measurable power: 0.1 watts
Measurement accuracy at power up to 10 watts: 0.1 watts
Measurement accuracy for power greater than 10 watts: 1 watt
Maximum installation inductance: 8.53μH
Minimum installation step of inductance: 0.05μH
Maximum installed capacity: 1869 pF
Minimum capacitance installation steps: 10 pF
Typical consumption 200-300 mA
Size: 155*88*38mm (excluding protrusions).
Weight: 0.45kg.
Simple instructions:
Before use, the antenna needs to be well grounded, and the RF inlet of the antenna is connected to the RF outlet of the short-wave machine with a radio frequency wire.
The RF outlet of the antenna is connected to the antenna (Recommended to set up a height of 3-6 meters above the ground and a length of 7-22 meters above 4 square meters. It is
recommended to take lightning protection measures at high places, such as lightning rods).
Connect to the antenna power plug (12~15VDC, generally shared with the shortwave machine).
Switch on the power of the short-wave machine, switch on the power of the antenna, and the equipment self-check shows normal.
Adjust the shortwave transmitter to the operating frequency, set the working mode to AM, FM, CW, or FT8, RTTY, etc. (the mode that can provide continuous carrier), press the shortwave transmitter or CW key to trigger the transmission, 10W power continuous transmission, At this time, the antenna tuning starts to adjust automatically. When the standing wave is less than 1.5, the antenna turner will
Parameter
Supply voltage range: 10-15 VDC(center is +)
Maximum working power: 150 watts
Minimum power required to start tuning: 5W
Minimum measurable power: 0.1 watts
Measurement accuracy at power up to 10 watts: 0.1 watts
Measurement accuracy for power greater than 10 watts: 1 watt
Maximum installation inductance: 8.53μH
Minimum installation step of inductance: 0.05μH
Maximum installed capacity: 1869 pF
Minimum capacitance installation steps: 10 pF
Typical consumption 200-300 mA
Size: 155*88*38mm (excluding protrusions).
Weight: 0.45kg.
Simple instructions:
Before use, the antenna needs to be well grounded, and the RF inlet of the antenna is connected to the RF outlet of the short-wave machine with a radio frequency wire.
The RF outlet of the antenna is connected to the antenna (Recommended to set up a height of 3-6 meters above the ground and a length of 7-22 meters above 4 square meters. It is
recommended to take lightning protection measures at high places, such as lightning rods).
Connect to the antenna power plug (12~15VDC, generally shared with the shortwave machine).
Switch on the power of the short-wave machine, switch on the power of the antenna, and the equipment self-check shows normal.
Adjust the shortwave transmitter to the operating frequency, set the working mode to AM, FM, CW, or FT8, RTTY, etc. (the mode that can provide continuous carrier), press the shortwave transmitter or CW key to trigger the transmission, 10W power continuous transmission, At this time, the antenna tuning starts to adjust automatically. When the standing wave is less than 1.5, the antenna turner will
Ada masalah dengan produk ini?
ULASAN PEMBELI
Belum ada ulasan untuk produk ini
Beli produk ini dan jadilah yang pertama memberikan ulasan