4.9/ 5.0
100% pembeli merasa puas
90 rating • 45 ulasan
5(82)91.11%
4(8)8.89%
3(0)0%
2(0)0%
1(0)0%
Atur jumlah dan catatan
Stok Total: Sisa 9
Subtotal
Rp92.500
Power Supply Module BEC APM2 2.5 APM Flight Controller Ardupilot Mega
Rp92.500
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: Multirotor
Features:
The APM 2.5, 2.6, 2.8, or 2.9, Pixhawk Power Module is a simple way of providing your APM 2.5, 2.6, 2.8, or 2.9 with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6-pos cable. The on-board switching regulator outputs 5.3V and a maximum of 2.25A from up to a 6S LiPo battery. The Power Module comes completely assembled with XT-60 connectors, and wrapped in shrink tubing for protection.
Used to detect the battery voltage and the battery current, flight control board receives two signals, calculate the remaining battery power, estimate the remaining flight time. In addition the module also comes with BEC function, you can output 5.3 DC, 3A maximum continuous current for the flight control board to provide a stable power supply. Another signal cable connectors are used in Japan original fittings, non-domestic joint, so APM flight control board and reliable connection between the power supply module.
Spesifikasi:
Max input voltage: 30V
Max current sensing: 90A
Size: 25*21*9mm
Net weight: 25gr
Weight : 35gr
Voltage and current measurement configured for 5V ADC
Switching regulator outputs 5.3V and 3A max
6-pos DF13 cable plugs directly to APM 2.5's, 2.6, 2.8, pixhawk 'PM' connector.
Note: The Power Module is only designed to power APM, a RC receiver and APM accessories (GPS, 3DR radio). It is not designed to power servos. Use your aircraft's own ESC/BEC for that.
The max. input voltage 30V, max. current measurable 90A, to achieve the control panel on battery power and voltage monitoring. The design parameters of voltage and current detector design parameters consistent with 3DR official ground station (mission planer) settings can be set directly refer to the official Wiki.
Isi Paket:
1x Power Module With XT60 Connectors for APM 2.5, 2.6, 2.8, or Pixhawk 2.4.8.
1x P cable 150mm.
Catatan:
- Untuk APM V3.1 perlu penyesuaian wiring dan konektor.
- Cocok untuk Pixhawk 2.4.8
The APM 2.5, 2.6, 2.8, or 2.9, Pixhawk Power Module is a simple way of providing your APM 2.5, 2.6, 2.8, or 2.9 with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6-pos cable. The on-board switching regulator outputs 5.3V and a maximum of 2.25A from up to a 6S LiPo battery. The Power Module comes completely assembled with XT-60 connectors, and wrapped in shrink tubing for protection.
Used to detect the battery voltage and the battery current, flight control board receives two signals, calculate the remaining battery power, estimate the remaining flight time. In addition the module also comes with BEC function, you can output 5.3 DC, 3A maximum continuous current for the flight control board to provide a stable power supply. Another signal cable connectors are used in Japan original fittings, non-domestic joint, so APM flight control board and reliable connection between the power supply module.
Spesifikasi:
Max input voltage: 30V
Max current sensing: 90A
Size: 25*21*9mm
Net weight: 25gr
Weight : 35gr
Voltage and current measurement configured for 5V ADC
Switching regulator outputs 5.3V and 3A max
6-pos DF13 cable plugs directly to APM 2.5's, 2.6, 2.8, pixhawk 'PM' connector.
Note: The Power Module is only designed to power APM, a RC receiver and APM accessories (GPS, 3DR radio). It is not designed to power servos. Use your aircraft's own ESC/BEC for that.
The max. input voltage 30V, max. current measurable 90A, to achieve the control panel on battery power and voltage monitoring. The design parameters of voltage and current detector design parameters consistent with 3DR official ground station (mission planer) settings can be set directly refer to the official Wiki.
Isi Paket:
1x Power Module With XT60 Connectors for APM 2.5, 2.6, 2.8, or Pixhawk 2.4.8.
1x P cable 150mm.
Catatan:
- Untuk APM V3.1 perlu penyesuaian wiring dan konektor.
- Cocok untuk Pixhawk 2.4.8
Ada masalah dengan produk ini?