Atur jumlah dan catatan
Stok Total: Sisa 1
Subtotal
Rp8.990.000
EVER ELECTRONICA STEP MOTOR DRIVER LW3D3070N0A1-00 MADE IN ITALY
Rp8.990.000
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: Semua Etalase
LW3D3070N0A1-00
Power supply voltage 24 [Vcc] ÷ 80 [Vcc]
Output current 1.7 [A/ph rms] ÷ 7.1 [A/ph rms] 2.4 [A/ph peak] ÷ 10.0 [A/ph peak]
Control mode Clock & Direction
Power stage H bridge bipolar chopper at 40 kHz.
Mounting Wall mounting
Digital inputs 4 optoisolated 2 - 24Vdc 2 MHzNPN or PNP or Line Driver.
Digital outputs 1 Digital OUT 24 Vdc - 100 mA for status monitoring
Step resolution From full step (200 pps - 1.8°) up to 1/256 (emulated).
Safety protections Over/Under voltage, Over Current, Over Temperature, Short Circuit Phase/Phase and Phase/Ground
Status monitoring 3 LED with guiding light (green and red/yellow)
Operative temperature 0 [°C]÷ 50 [°C]
Storage temperature 0 [°C] ÷ 55 [°C]
Humidity 0 [%] ÷ 90 [%]
Protection class IP20
Dimensions H x L x W 128.0 [mm] x 30.0 [mm] x 74.0 [mm]
Functions
● Setting of the current value by means of dip-switches
● Selection of the step angle by means of roto-switches. In order to maintain compatibility with traditional drivers, step angles have been emulated through software, the current regulation is always sinusoidal.
● Possibility to select five user functions:
1 - Reading the motor BEMF, LW3 drivers detect without encoder the step loss, showing alarm status with the Fault digital OUT and a LED sequence.
2 - Step/Direction or Clock-Up / Clock-Down control mode.
3 - enable input management (safety control).
4 - 30% or 70% automatic current reduction (still motor). 5 - enabling of “Clock Test” function, useful during the driver’s installation, which shows the right presence of the clock signal through status LED flashing.
Power supply voltage 24 [Vcc] ÷ 80 [Vcc]
Output current 1.7 [A/ph rms] ÷ 7.1 [A/ph rms] 2.4 [A/ph peak] ÷ 10.0 [A/ph peak]
Control mode Clock & Direction
Power stage H bridge bipolar chopper at 40 kHz.
Mounting Wall mounting
Digital inputs 4 optoisolated 2 - 24Vdc 2 MHzNPN or PNP or Line Driver.
Digital outputs 1 Digital OUT 24 Vdc - 100 mA for status monitoring
Step resolution From full step (200 pps - 1.8°) up to 1/256 (emulated).
Safety protections Over/Under voltage, Over Current, Over Temperature, Short Circuit Phase/Phase and Phase/Ground
Status monitoring 3 LED with guiding light (green and red/yellow)
Operative temperature 0 [°C]÷ 50 [°C]
Storage temperature 0 [°C] ÷ 55 [°C]
Humidity 0 [%] ÷ 90 [%]
Protection class IP20
Dimensions H x L x W 128.0 [mm] x 30.0 [mm] x 74.0 [mm]
Functions
● Setting of the current value by means of dip-switches
● Selection of the step angle by means of roto-switches. In order to maintain compatibility with traditional drivers, step angles have been emulated through software, the current regulation is always sinusoidal.
● Possibility to select five user functions:
1 - Reading the motor BEMF, LW3 drivers detect without encoder the step loss, showing alarm status with the Fault digital OUT and a LED sequence.
2 - Step/Direction or Clock-Up / Clock-Down control mode.
3 - enable input management (safety control).
4 - 30% or 70% automatic current reduction (still motor). 5 - enabling of “Clock Test” function, useful during the driver’s installation, which shows the right presence of the clock signal through status LED flashing.
Ada masalah dengan produk ini?
ULASAN PEMBELI
Belum ada ulasan untuk produk ini
Beli produk ini dan jadilah yang pertama memberikan ulasan