Atur jumlah dan catatan
Stok Total: 99
Subtotal
Rp405.000
Betaflight Omnibus F4 Pro V2 Flight Controller Builtin OSD BEC untu b0
Rp405.000
- Kondisi: Baru
- Waktu Preorder: 30 Hari
- Min. Pemesanan: 1 Buah
- Etalase: Hobi
Betaflight Omnibus F4 Pro V2 Flight Controller Builtin OSD BEC untuk FPV Drone
Pre-Order. Perkiraan Sampai Alamat 10-15 Hari
Beli DISINI, dari China sudah termasuk PAJAK
Garansi Uang kembali apabila barang Rusak, Beda Ukuran/Produk
Note:
- Never flash the flight controller with anything other than REVO firmware.
- Each flight controllers are flashed with latest BetaFlight firmware available at the time of shipping. Thus all the flight controller is in working condition.
Package Included:
- 1 x F4 OMNIBUS V2 PRO Flight Controller
Features:
- Size: Approx. 36mm
- STM32 F405 MPU
- This flight control is designed for FPV racing drone
- Upgraded F4 Processor
- Low Noise Stable SPI Gyro and Barometer
- BetaFlight OSD (Easy OSD programming right from Configurator)
- Built-in Voltage/Current sensor (need Club24A mod)
- D-Shot 1200 Support
- Direct LiPo input no BEC required
- MicroSD card slot for BlackBox logging
- Spektrum satellite receiver port (UART1)
- Bootloader Button
- MPU6000 6 axis SPI Gyro & Accelerometer
- BMP280 Barometer onboard
- Tune your PIDs on the go using your Transmitter
- TBS SmartAudio V2via TX6 on J10
- DFU Bootloader button
- Pre-Flashed with BetaFlight 3.1.x (Target: OMNIBUSF4SD)
Flashing Instructions:
1. Press and hold the boot button and plug the flight controller to the computer
2. Open Zadig Options > List All Devices
3. From Drop down menu select STM32 Bootloader
4. Replace existing drivers with WinUSB (v6.1.7600.xxxxx)
5. After successful installation unplug, then re-plug USB cable with Boot button pressed
6. Open BetaFlight configurator, you should see DFU in the top right corner
7. Select Firmware Flasher tab from the left side panel
8. Choose a board >
Pre-Order. Perkiraan Sampai Alamat 10-15 Hari
Beli DISINI, dari China sudah termasuk PAJAK
Garansi Uang kembali apabila barang Rusak, Beda Ukuran/Produk
Note:
- Never flash the flight controller with anything other than REVO firmware.
- Each flight controllers are flashed with latest BetaFlight firmware available at the time of shipping. Thus all the flight controller is in working condition.
Package Included:
- 1 x F4 OMNIBUS V2 PRO Flight Controller
Features:
- Size: Approx. 36mm
- STM32 F405 MPU
- This flight control is designed for FPV racing drone
- Upgraded F4 Processor
- Low Noise Stable SPI Gyro and Barometer
- BetaFlight OSD (Easy OSD programming right from Configurator)
- Built-in Voltage/Current sensor (need Club24A mod)
- D-Shot 1200 Support
- Direct LiPo input no BEC required
- MicroSD card slot for BlackBox logging
- Spektrum satellite receiver port (UART1)
- Bootloader Button
- MPU6000 6 axis SPI Gyro & Accelerometer
- BMP280 Barometer onboard
- Tune your PIDs on the go using your Transmitter
- TBS SmartAudio V2via TX6 on J10
- DFU Bootloader button
- Pre-Flashed with BetaFlight 3.1.x (Target: OMNIBUSF4SD)
Flashing Instructions:
1. Press and hold the boot button and plug the flight controller to the computer
2. Open Zadig Options > List All Devices
3. From Drop down menu select STM32 Bootloader
4. Replace existing drivers with WinUSB (v6.1.7600.xxxxx)
5. After successful installation unplug, then re-plug USB cable with Boot button pressed
6. Open BetaFlight configurator, you should see DFU in the top right corner
7. Select Firmware Flasher tab from the left side panel
8. Choose a board >
Ada masalah dengan produk ini?
ULASAN PEMBELI
Belum ada ulasan untuk produk ini
Beli produk ini dan jadilah yang pertama memberikan ulasan