Atur jumlah dan catatan
Stok Total: 122
Subtotal
Rp216.000
ELRS 2.4G Receiver Mini ExpressLRS 2.4G RX Nano 2400RX EP1 EP2 Long Range CYCLONE CRSF Betaflight For RC FPV Drone
Rp216.000
- Kondisi: Baru
- Waktu Preorder: 30 Hari
- Min. Pemesanan: 1 Buah
- Etalase: Semua Etalase
Brand Name : XDRC
Model Number : Nano 2400RX
Size : 17mm*10.5mm*3mm
Material : Composite Material
Origin : Mainland China
Use : Vehicles & Remote Control Toys
Quantity : 1 pcs
RC Parts & Accs : RECEIVERS
For Vehicle Type : Airplanes
Tool Supplies : Assembled class
Upgrade Parts/Accessories : Receivers
Remote Control Peripherals/Devices : RECEIVERS
Recommend Age : 14+y
Is Electric : No battery
Hign-concerned Chemical : None
The CYCLONE series receiver is based on the open-source architecture and program of ExpressLRSI. ESP8285MCU is used. You can upgrade the firmware through WIFI, which is very friendly. Usually, you only need to power up the receiver and turn off the remote control. By default, you can find the hotspot of LExpressLRSE 60 seconds later. Connect to the hotspot through a computer or mobile phone. The key is expressIrs. Then you can access 10.0.0.1 to upload the receiver firmware.
Nano 2400RX receiver with power amplifier (PA+LNA). Therefore, it has 100mW telemetry output and better sensitivity at longer distances. It uses IPEX1 1st generation antenna pedestal and external T antenna (customized by professional factory, each antenna has been tested by a professional device to ensure quality, lightness and durability).
Because of the low latency and high refresh rate RF modules of the ELRS Nano receiver, they are very suitable for FPV competitions and long-range. At the same time, these receivers have ultra light and ultra small dimensions.
Nano 2400RX
Firmware: BETAFPV 2400RX
Type: ISM
Antenna Interface: IPEX1
Max Refresh Rate: 500Hz
Min Refresh Rate: 25Hz
Working Voltage: 45.5V
Weight: 0.65g
Size: 17mm*10.5mm*3mm
Protocol: CRSF (Betaflight)
Product List:
Nano 2400RX *1
T Antenna *1
30# connecting wire *4 (black, red, white, yellow)
Heat Shrinkable Sleeve *1
Configuration & Bind:
1. Please check the software version number of the ELRS module or the built-in ELRS module first. At present, there are only general version numbers of 1. or 2. Please confirm that the module and receiver are the same general version. (For example, the module with version 2.0.1 can be used normally with the receiver with version 2.3.0, so it is not necessary to upgrade the module firmware.) However, for better compatibility, it is recommended that the module and receiver be upgraded to the same version.
2. The LED will start to double flash after the receiver is powered on and off for three times, which means the receiver enters the frequency matching mode. Enter Module Binding operation.
3. After the setting is successful, the LED on the receiver will become normally on, and the telemetry signal can also be received.
4. Meaning of receiver LED status:
The LED is always on, indicating successful frequency matching or normal connection and communication
The double flashing LED indicates that the frequency is being aligned.
The slow flashing LED indicates that the transmitter signal cannot be received.
The rapid flashing LED indicates that the wifi communication mode can be updated through the computer or mobile phone.
Model Number : Nano 2400RX
Size : 17mm*10.5mm*3mm
Material : Composite Material
Origin : Mainland China
Use : Vehicles & Remote Control Toys
Quantity : 1 pcs
RC Parts & Accs : RECEIVERS
For Vehicle Type : Airplanes
Tool Supplies : Assembled class
Upgrade Parts/Accessories : Receivers
Remote Control Peripherals/Devices : RECEIVERS
Recommend Age : 14+y
Is Electric : No battery
Hign-concerned Chemical : None
The CYCLONE series receiver is based on the open-source architecture and program of ExpressLRSI. ESP8285MCU is used. You can upgrade the firmware through WIFI, which is very friendly. Usually, you only need to power up the receiver and turn off the remote control. By default, you can find the hotspot of LExpressLRSE 60 seconds later. Connect to the hotspot through a computer or mobile phone. The key is expressIrs. Then you can access 10.0.0.1 to upload the receiver firmware.
Nano 2400RX receiver with power amplifier (PA+LNA). Therefore, it has 100mW telemetry output and better sensitivity at longer distances. It uses IPEX1 1st generation antenna pedestal and external T antenna (customized by professional factory, each antenna has been tested by a professional device to ensure quality, lightness and durability).
Because of the low latency and high refresh rate RF modules of the ELRS Nano receiver, they are very suitable for FPV competitions and long-range. At the same time, these receivers have ultra light and ultra small dimensions.
Nano 2400RX
Firmware: BETAFPV 2400RX
Type: ISM
Antenna Interface: IPEX1
Max Refresh Rate: 500Hz
Min Refresh Rate: 25Hz
Working Voltage: 45.5V
Weight: 0.65g
Size: 17mm*10.5mm*3mm
Protocol: CRSF (Betaflight)
Product List:
Nano 2400RX *1
T Antenna *1
30# connecting wire *4 (black, red, white, yellow)
Heat Shrinkable Sleeve *1
Configuration & Bind:
1. Please check the software version number of the ELRS module or the built-in ELRS module first. At present, there are only general version numbers of 1. or 2. Please confirm that the module and receiver are the same general version. (For example, the module with version 2.0.1 can be used normally with the receiver with version 2.3.0, so it is not necessary to upgrade the module firmware.) However, for better compatibility, it is recommended that the module and receiver be upgraded to the same version.
2. The LED will start to double flash after the receiver is powered on and off for three times, which means the receiver enters the frequency matching mode. Enter Module Binding operation.
3. After the setting is successful, the LED on the receiver will become normally on, and the telemetry signal can also be received.
4. Meaning of receiver LED status:
The LED is always on, indicating successful frequency matching or normal connection and communication
The double flashing LED indicates that the frequency is being aligned.
The slow flashing LED indicates that the transmitter signal cannot be received.
The rapid flashing LED indicates that the wifi communication mode can be updated through the computer or mobile phone.
Ada masalah dengan produk ini?
ULASAN PEMBELI
Belum ada ulasan untuk produk ini
Beli produk ini dan jadilah yang pertama memberikan ulasan