5.0/ 5.0
100% pembeli merasa puas
4 rating • 2 ulasan
5(4)100%
4(0)0%
3(0)0%
2(0)0%
1(0)0%
Atur jumlah dan catatan
Stok: Habis
Subtotal
-
RX Receiver NB4 Built in Gyro Micro V6 Flysky Noble NB4 RX - Case only
Rp140.000
Pilih rx nb4: Case only
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: Gyro - RX TX
Package List :
1x RX With Gyro NB4
4x jst cable1.5 3pin
This 2.4G RC receiver uses AFHDS3 protocol and it is dedicated to the FLYSKY Noble NB4 transmitter. It has single-antenna, use two-way transmission and features a unique compact design that saves space.
Features:
1. FLYSKY AFHDS3 protocol compatible
2. High performance CPU enhance precision control feeling
3. Integrated high performance dual sensitivity GYRO with EPA setup
4. Tower antenna provides both good receipt signal and
space saving
5. Nano size (19mm x 12mm)
6. Added failsafe function
7. Operating Voltage 3.5V-12V
8. Weight: 3g
Binding:
1. Press the BIND button and power on the receiver, the receiver's led will flash quickly.
2. Put the transmitter into bind mode. The receiver's led will flash slowly when the binding is successful.
3. Disconnect receiver's power and reconnect the powercable to the receiver. Now is should working normally.
GYRO sensitivity Adjustment:
The gyro sensitivity is controlled by CH3 value which could be adjusted on the transmitter. When the CH3 value is 50%, the sensitivity is zero. Turn CH3 value to 0% or 100% both can reach 100% sensitivity. Turn CH3 value to 0% or turn CH3 value to 100% will have different sensitivity curve. The GYRO provides 2 different optimized sensitivity curves for drifting.
EPA (Travel) Setting :
Press the "SETUP" button, turn on the GYRO. When the LED starts blinking fast, wait for the LED to blink slowly and the gyroscope is now in EPA (travel) setup mode, release the "SETUP" button. First turn the remote control to the Left (FORWARD Gyro setup) or Right (REVERSE Gyro Setup) "EPA" position (the left end of the chassis) and stop there for a few seconds, when the left "EPA" position is saved in the gyroscope, the servo will automatically return to the middle position. Then turn the remote to the correct "EPA" position (right end position of the chassis) and stop there for a few seconds, when the correct "EPA" position
1x RX With Gyro NB4
4x jst cable1.5 3pin
This 2.4G RC receiver uses AFHDS3 protocol and it is dedicated to the FLYSKY Noble NB4 transmitter. It has single-antenna, use two-way transmission and features a unique compact design that saves space.
Features:
1. FLYSKY AFHDS3 protocol compatible
2. High performance CPU enhance precision control feeling
3. Integrated high performance dual sensitivity GYRO with EPA setup
4. Tower antenna provides both good receipt signal and
space saving
5. Nano size (19mm x 12mm)
6. Added failsafe function
7. Operating Voltage 3.5V-12V
8. Weight: 3g
Binding:
1. Press the BIND button and power on the receiver, the receiver's led will flash quickly.
2. Put the transmitter into bind mode. The receiver's led will flash slowly when the binding is successful.
3. Disconnect receiver's power and reconnect the powercable to the receiver. Now is should working normally.
GYRO sensitivity Adjustment:
The gyro sensitivity is controlled by CH3 value which could be adjusted on the transmitter. When the CH3 value is 50%, the sensitivity is zero. Turn CH3 value to 0% or 100% both can reach 100% sensitivity. Turn CH3 value to 0% or turn CH3 value to 100% will have different sensitivity curve. The GYRO provides 2 different optimized sensitivity curves for drifting.
EPA (Travel) Setting :
Press the "SETUP" button, turn on the GYRO. When the LED starts blinking fast, wait for the LED to blink slowly and the gyroscope is now in EPA (travel) setup mode, release the "SETUP" button. First turn the remote control to the Left (FORWARD Gyro setup) or Right (REVERSE Gyro Setup) "EPA" position (the left end of the chassis) and stop there for a few seconds, when the left "EPA" position is saved in the gyroscope, the servo will automatically return to the middle position. Then turn the remote to the correct "EPA" position (right end position of the chassis) and stop there for a few seconds, when the correct "EPA" position
Ada masalah dengan produk ini?