IBlu 2pcs/lot LoRa32u4 II Development Board 868MHz 915MHz Lora Module IOT SX1276 HPD13 Wifi Transceiver Module Antenna JST Connector

SELAMAT DATANG DITOKO SAYA. Untuk kualiatas produknya pastinya terjamin asli bukan kw. Harga dan Stock bisa berubah sewaktu waktu. Mohon Chat Admin Toko saya terlebih dahulu sebelum Order yaa..
Brand Name : DIYmall
Model Number : DIY0051N
Origin : Mainland China
Quantity : 2pcs/lot
2pcs/lot LoRa32u4 II Development Board 868MHz 915MHz Lora Module IOT SX1276 HPD13 Wifi Transceiver Module Antenna JST Connector
LoRa32u4 II
LoRa32u4 II is a light and low consumption board based on the Atmega32u4 and HPD13 868MHz LoRA module and an USB battery charging circuit. Ideal for creating long range wireless networks that can exceed 2.4 GHz 802.15.4 and similar, it is more flexible than Bluetooth LE, does not require high power unlike WiFi and offers long range.
The ATmega32u4 is clocked at 8 MHz and 3.3 V. This chip has 32 K of flash, 2 K of RAM and built-in USB to Serial communication, debugging and programming capabilities without the need for an external FTDI chip, it can also act as an HID device (mouse, keyboard, USB MIDI device, etc).
This board is also equipped with a LiPo and Liion charging circuit and a standard battery interface. It is fully compatible with Arduino. A white user led is tied to pin 13. An orange LED is used for charging status.
HPD13 wireless module, using high-performance, highly integrated RF transceiver chip SX1276 design. Advanced LoRaTM spread spectrum communication technology to ensure that the module communication distance and anti-jamming capability greatly improved, and also achieved a very low current consumption. In the LoRaTM mode, the HPD13 provides higher reception sensitivity performance, more robust anti-jamming capability, and improved communication distance and reliability compared to the same transmit and receive modules on the market. In normal (G) FSK mode, it also provides industry-specific receiver sensitivity, as well as very high communication rates.
ATmega32u4 8MHz with 3.3V logic/power
3.3V regulator with 500mA peak current output
USB native support, comes with USB bootloader and serial port debugging
Built in 100mA lipoly charger with charging status indicator LED
Reset button
HPD13:
Receive current: 10 ~ 14mA
Interface Type: SPI
Operating temperature: -40 C to + 85 C
Digital RSSI function
Automatic frequency correction
Automatic gain control
Radio wake-up function
Low voltage detection and temperature sensor
Fast wakeup with frequency hopping
Highly configurable packet handlers
USAGE
1. LoRa DIO1 is now connected by default to Atmega32u4 pin 5 (PC6) allowing direct use of LMIC and other LoRaWAN libraries without soldering, it is still possible to disable this link by opening the DIO1 solder jumper on topside.
2. LoRa DIO2 and DIO3 are now routing to Atmega32u4 pin 6 (PD7) and 14 (PD5), solder jumpers are open by default (these DIO pins are rarely used).
3. Atmega32u4 pins 0 (PD2),1 (PD3) for UART and 2 (PD1), 3 (PD0) for I2C are now free for use.
4. LoRa DIO pins solder jumpers have been moved on topside for better accessibility.
5. Pull-up resistors (4.7K) have been added on the I2C bus.
6. The antenna uFL connector has been moved on topside to ease access.
Document link:
UL1007-26AWG Electronic Wire
Description:
Electronic wire: UL1007-26AWG standard line 7 / 0.16MM,80 degrees 300V
Outside diameter: 1.3MM
Using Terminal Model: JST-PH2.0MM spacing -2P
Color arrangement: The first hole is black line = 96MM,The second hole is red line = 88MM
Tail Popi: 2MM green on the tin
868MHz 915MHz GSM IPX IPEX 1.13 UF.L Antenna Built-in 2DBi 8CM
Frequency: 824-960MHz
Gain: 2DBi
Length: Total is 8CM
Standing wave ratio / S.W.R.2.0
Impedance: 50
Max Input power: 50W
RF Cable: RG1.13 cable
IPEX 850-1850MHz
Frequency:850-960/1710-1880MHz
Type: U.FL to Female SMA
Impedance: 50 ohms
Gain: 2DBi