IBlu Skystars F7HD Pro4 Flight Controller FPV KM65 128K BL32 4IN1 ESC Jupiter BLHeli-32 Stack DS1200 for FPV Racing Drone

SELAMAT DATANG DITOKO SAYA. Untuk kualiatas produknya pastinya terjamin asli bukan kw. Harga dan Stock bisa berubah sewaktu waktu. Mohon Chat Admin Toko saya terlebih dahulu sebelum Order yaa..
Brand Name : vifly
Model Number : F7+KM65 Blheli_32 128K F4 Fly Stack
Material : Composite Material
Origin : Mainland China
Use : Vehicles & Remote Control Toys
Wheelbase : Bottom Plate
Recommend Age : 14+y
Is Electric : No battery
Hign-concerned Chemical : None
What makes this FC PRO4 different from others?
1. Solder pads are the largest in size compared to other FC in market.
2. Proper solder pad spacing to avoid solder bridge and facilitate easy soldering.
3. ESC connector on top-side rather than bottom which makes it easy for repair.
4. TVS Diode for Reverse Polarity Protection and Voltage Spike Suppression.
5. Powerful 3A BECto supply all your electronics.
6. Pads arrangement are executed in such a way that when you twist the wires of the camera VTX and RX you don't get any wire overlapping this gives you a uniform twist and clean look.
7. SupportDJI O3 connectoron the top side.
8. Support VTX ON/OFF Pit Switch.
9. Gyroscope independent power supply, No power lines near MPU6000 Gyroto avoid any EMI interference.
10. Two stages of Quality check to reduce any faulty electronic.
11. Comes ready with I2C support and INAV.
FC Specifications:
MCU: STM32F722RET6 216MHz
Gyroscope: MPU6000
Baro:Bmp280
OSD: Betaflight SPI OSD DJI HD OSD(UART6)
Black box: 16MB
6x Uarts: UART 1/2/3/4/5/6
4x PWM outputs
1x I2C
3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red)
USB Type-C(USB2.0)
1x JST-SH1.0_8pin connector (Gnd/Vbat/S1/S2/S3/S4/Rx3/Curr)
1x JST-SH1.0_6pin connector (10V/Gnd/TX6/RX6/Gnd/Sbus)
VTX 10V/Vbat filtered power ON/OFFPitswitch
DJI FPV OSD is supported by any spare UART
LED: 4 LED independent pads, support WS2812 programming lamp output.
Receiver: Support Sbus, crsf, ibus, SBUS, XBUS, support 3.3v Spektrum satellite receiver, The default receiver input is UART1(You can solder ELRS RX on UART1), F7 has a built-in inverter, which can actually be installed in any spare UART.
Power:
Input voltage: 3-6S
BEC: 5V/10V 3A dual-channel BEC supports stable power supply on the sky side of DJIO3
LDO 3.3V: Max.250mA
FC Firmware:
BetaFlight firmware: SKYSTARSF722Pro
INAV firmware:SKYSTARSF722HD
Mounting:
Installation size: 30.5mm 30.5mm The installation hole is M4 and supports shock column installation
External size 39mm 39mm
Flight control weight: 6.9g
Flight control onboard voltage sensor.
BL32-65A 4IN1 3-6S ESC BLheli32 128K DS1200 4-in-1 ESC:
Support 128K Ds1200, Ds600, Ds300, Ds150, Ones125, Multis, PWM control signal
1. Excellent over-current capability.
2. Extreme stably support 6S LiPo batterywith TVS.
3. Excellent heat dissipation performance
4. Better control performance F4 core MCU support 128K.
Input voltage: 3-6S LiPo
Con.Current: 65A
Peak Current: 90A 10S
Firmware: BLHeli_32
Support : Ds 600/1200
Mounting hole : 30.5mm/M3
BEC: No
Product size: 45.6*45*7.6mm
Weight: 19g
Including
1x F7HD Pro4FC
1x KM65128K BL32 4IN1 ESC
8x Silicon grommets M4 to M3
2x JST-SH1.0_8pin cable, 4cm
1x JST-GH-6P cable for DJI port, 10cm
AM60 AM_32 60A 32Bit 3-6S 4in1 ESC
Specifications
Input voltage: 3-6S LiPo
Con.Current: 60A
Peak Current: 70A 10S
Firmware: AM_32
Support: Ds 600/1200
Mounting hole : 30.5X30.5 mm/M3
BEC: No
Product size: 41*46*7.6mm
Weight: 18g
Includes
1x Skystars AM60 AM_32 60A 32Bit 3-6S 30.5mm 4in1 ESC
4X Silicon grommets M3X3.5mm
1 x XT60 Connected Cable
1 x Cable
1 x Capacitor 35V 560uF