IBlu SpeedyBee F405 WING MINI Fixed Wing Flight Controller 2-6S LiPo for RC Fixed Wing Model Airplane Drone

SELAMAT DATANG DITOKO SAYA. Untuk kualiatas produknya pastinya terjamin asli bukan kw. Harga dan Stock bisa berubah sewaktu waktu. Mohon Chat Admin Toko saya terlebih dahulu sebelum Order yaa..
Model Number : SpeedyBee F405 WING MINI Fixed Wing Flight Controller
Size : AN
Material : Composite Material
Origin : Mainland China
Use : Vehicles & Remote Control Toys
Quantity : 1 pcs
Wheelbase : Bottom Plate
RC Parts & Accs : F405 WING MINI
For Vehicle Type : Airplanes
Tool Supplies : Assembly Category
Technical parameters : KV1100
Four-wheel Drive Attributes : Assemblage
Upgrade Parts/Accessories : Flight Controller
Remote Control Peripherals/Devices : Remote Controller
Recommend Age : 14+y
Is Electric : No battery
Hign-concerned Chemical : None
Specifications
Product Name
SpeedyBee F405 WING MINI FC board
MCU
STM32F405, 168MHz, 1MB Flash
IMU(Gyro&Accelerometer)
ICM-42688-P
Barometer
SPL006-001
OSD Chip
AT7456E
Blackbox
MicroSD Card Slot
UART
6 sets (USART1, USART2, USART3, UART4, UART5,
UART6 - Dedicated for Wireless board Telemetry connection)
I2C
1x Used for magnetometer, digital airspeed sensor
ADC
4x (VBAT, Current, Analog RSSI, Analog AirSpeed)
PWM
12x (9x pin headers + 2x solder pads + 1x "LED" pad)
ELRS/CRSF Receiver
Supported, connected to UART1
SBUS
Built-in inverter for SBUS input (UART2-RX)
LED
3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator (Red)
Analog RSSI
Supported, Named as "RS"
Dual Analog Camera Switching
Default to Camera1 Video Input (C1). Switch between C1 and C2 using ArduPilot Relay or INAV Modes/USER.
Both cameras should have the same video format, either PAL or NTSC.
Supported FC Firmware
INAV: SpeedyBeeF405WING (default)
ArduPilot: SpeedyBeeF405WING
Weight
5.6g
Product Name
SpeedyBee F405 WING MINI PDB board
Input voltage range
7~26V (2~6S LiPo)
Battery Voltage Sensor
Connect to FC board VBAT, 1K:10K (Scale 1100 in INAV, BATT_VOLT_MULT 11.0 in ArduPilot)
Battery Current Sensor
80A continuous, 150A peak Connect to FC board Current (Scale 195 in INAV, 50 A/V in ArduPilot)
TVS Protective diode
Yes
FC BEC output
Output 5.2V +/- 0.1V DC Continuous current 2 Amps, 3A Peak Designed for FC, Receiver, GPS module, AirSpeed Sensor, Telemetry module
VTX & Camera power supply
The VTX power interface Vv offers two power supply options: direct battery voltage or integrated BEC 5V (sharing the 5V4A Servo BEC voltage)
By default, it is set to battery voltage
(Ensure the VTX and camera input voltage range is compatible)
Switching to 5V power supply is possible via pad jumper (using Servo BEC output)
(If using this method, ensure the current requirements for both servo and VTX are sufficient)
Servo BEC output
Output 5V +/- 0.1V DC Continuous current 4 Amps, 5A Peak Voltage adjustable, 5V Default, 6V via jumper Designed for Servos.
Weight
5.5g
Product Name
SpeedyBee F405 WING MINI Wireless USB Extender
Wireless Configuration (long press BOOT button for 6 seconds to switch modes)
INAV:Please make sure the MSP switch on UART 6 is turned on and set to a baud rate of 115200 ArduPilot:Please make sure the Serial 6 is set to baud rate 115200 and protocol Mavlink2
BLE mode, connect to Speedybee APP
Wi-Fi (AP)mode, able to connect to Speedybee APP, QGroundControl APP, MissionPlanner, etc. WiFi: SpeedybeeeFLY-WIFI Password:
Wi-Fi (STA)mode, able to connect to QGroundControl APP, MissionPlanner, etc.
Step 1: turn on Personal spot;
Step 2: Set spot, locate NAME/Device Name/spot name/etc.
Step 3: change the current name to eFLY and the password is,
Wireless off mode
USB Port Type
Type-C
Buzzer
5V Active Buzzer
Weight
3.2g