Atur jumlah dan catatan
Stok Total: 109
Subtotal
Rp312.000
JuaL 3pcs Smart Electronics CD74HC4067 16-Channel og Digital
Rp312.000
- Kondisi: Baru
- Waktu Preorder: 15 Hari
- Min. Pemesanan: 1 Buah
- Etalase: Tools Industri Import
3pcs Smart Electronics CD74HC4067 16-Channel og Digital Multiplexer PCB Board Module Geekcreit for Arduino - products that work with official Arduino boards
Semua Produk Di Toko Kami PO (Personal Pre-Order) 7-10 Hari Tergantung Stok Dan Posisi Gudang. Harap Chat Terlebih Dahulu Sebelum Order Atau Anda Setuju Dengan Waktu Pre-Order Yang Kami Tetapkan Secara Default 15-Hari
Specifications:
1.2V to 6V operation
2.“On” resistance: 70 Ohms @ 4.5V
3.6ns break-before-make @ 4.5V
4.Wide operating temperature range: -50°C to 125°C
Features
- This is a pcb board for the very handy 16-Channel og/Digital Multiplexer/Demultiplexer CD74HC4067.
- This chip is like a rotary switch - it internally routes the common pin
to one of 16 channel pins (CHANxx).
- It works with both digital and og signals (the voltage can't be higher than VCC),and the connections function in either direction.
- To control it, connect 4 digital outputs to the chip's address select pins (S0-S3),and send it the binary address of the channel you want.
- This allows you to connect up to 16 sensors to your system using only 5 pins!
- You can use it to pipe TTL-level serial to or from multiple devices.
For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller.
You can then select any one of those 16 devices to listen to.
If you want two-way communications, you can add a second board to route
your microcontroller's TX line to 16 device's RX lines.
By using multiple boards, you can create similar arrangements for I2C, SPI, etc.
The internal switches are bidirectional, support voltages between ground and VCC,
have low “on” resistance and low “off” leakage, and to prevent crosstalk, perform “break-before-make” switching.
The board also breaks out the chip's “enable” pin, which when driven high,
will completely disconnect the
ID-1630085
Semua Produk Di Toko Kami PO (Personal Pre-Order) 7-10 Hari Tergantung Stok Dan Posisi Gudang. Harap Chat Terlebih Dahulu Sebelum Order Atau Anda Setuju Dengan Waktu Pre-Order Yang Kami Tetapkan Secara Default 15-Hari
Specifications:
1.2V to 6V operation
2.“On” resistance: 70 Ohms @ 4.5V
3.6ns break-before-make @ 4.5V
4.Wide operating temperature range: -50°C to 125°C
Features
- This is a pcb board for the very handy 16-Channel og/Digital Multiplexer/Demultiplexer CD74HC4067.
- This chip is like a rotary switch - it internally routes the common pin
to one of 16 channel pins (CHANxx).
- It works with both digital and og signals (the voltage can't be higher than VCC),and the connections function in either direction.
- To control it, connect 4 digital outputs to the chip's address select pins (S0-S3),and send it the binary address of the channel you want.
- This allows you to connect up to 16 sensors to your system using only 5 pins!
- You can use it to pipe TTL-level serial to or from multiple devices.
For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller.
You can then select any one of those 16 devices to listen to.
If you want two-way communications, you can add a second board to route
your microcontroller's TX line to 16 device's RX lines.
By using multiple boards, you can create similar arrangements for I2C, SPI, etc.
The internal switches are bidirectional, support voltages between ground and VCC,
have low “on” resistance and low “off” leakage, and to prevent crosstalk, perform “break-before-make” switching.
The board also breaks out the chip's “enable” pin, which when driven high,
will completely disconnect the
ID-1630085
Ada masalah dengan produk ini?
ULASAN PEMBELI
Belum ada ulasan untuk produk ini
Beli produk ini dan jadilah yang pertama memberikan ulasan