Atur jumlah dan catatan
Stok Total: Sisa 4
Subtotal
Rp28.500.000
Notifier AMPS-24E Power Supply For NFS-3030 NFS2-3030
Rp28.500.000
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: NOTIFIER
General
NOTIFIER’s AMPS-24/E is an addressable power supply and
battery charger with up to three 24 VDC outputs. It operates in
either FlashScan or CLIP (Classic Loop Interface Protocol)
mode with the NFS-3030/NFS2-3030 Fire Alarm Control Panel
(FACP). It can also be used as the primary power supply for
the NCA-2 Network Control Annunciator.
Features
• Addressable by NFS-3030/NFS2-3030 FACP.
• Selectable charging current charges 7 AH to 200 AH batteries.
• Isolated Signaling Line Circuit (SLC) interface.
• Trouble bus input for use with normally-open dry contacts or
open-collector circuit.
• USB Type B connector for programming installation parameters.
• Brownout detection.
• Battery/battery charger supervision.
• Secondary Power Auxiliary Outputs: 24V @ 0.5A and 5V @
0.15A.
• AC loss detection and AC loss delay reporting.
• Mounts in a CAB-4 Series enclosure, EQ Cabinet Series
enclosure, BB-25, BB-100, or BB-200 Battery Backbox.
Specifications
• Primary (AC) power:
AMPS24: 110-120 VAC 50/60 Hz input, 5 A maximum;
AMPS24E: 220-240 VAC 50/60 Hz input, 2.5 A maximum.
• MAIN 24V Output - filtered power-limited power. Refer to
table for configuration/current information.
• AUX 24V - provides filtered power-limited power for additional components. Refer to table above for configuration/
current information.
• Secondary power (battery) charging circuit: Current-limited,
sealed lead-acid battery charger which will charge 7 to 200
AH batteries.
Selectable charging current: 1.0 A, 2.0 A or 5.0 A.
• Secondary power auxiliary outputs.
• Wire sizes: 10 AWG (5.26 mm²) to 22 AWG (0.326 mm²).
• Battery fuse (F2): 15 A, fast-acting.
NOTIFIER’s AMPS-24/E is an addressable power supply and
battery charger with up to three 24 VDC outputs. It operates in
either FlashScan or CLIP (Classic Loop Interface Protocol)
mode with the NFS-3030/NFS2-3030 Fire Alarm Control Panel
(FACP). It can also be used as the primary power supply for
the NCA-2 Network Control Annunciator.
Features
• Addressable by NFS-3030/NFS2-3030 FACP.
• Selectable charging current charges 7 AH to 200 AH batteries.
• Isolated Signaling Line Circuit (SLC) interface.
• Trouble bus input for use with normally-open dry contacts or
open-collector circuit.
• USB Type B connector for programming installation parameters.
• Brownout detection.
• Battery/battery charger supervision.
• Secondary Power Auxiliary Outputs: 24V @ 0.5A and 5V @
0.15A.
• AC loss detection and AC loss delay reporting.
• Mounts in a CAB-4 Series enclosure, EQ Cabinet Series
enclosure, BB-25, BB-100, or BB-200 Battery Backbox.
Specifications
• Primary (AC) power:
AMPS24: 110-120 VAC 50/60 Hz input, 5 A maximum;
AMPS24E: 220-240 VAC 50/60 Hz input, 2.5 A maximum.
• MAIN 24V Output - filtered power-limited power. Refer to
table for configuration/current information.
• AUX 24V - provides filtered power-limited power for additional components. Refer to table above for configuration/
current information.
• Secondary power (battery) charging circuit: Current-limited,
sealed lead-acid battery charger which will charge 7 to 200
AH batteries.
Selectable charging current: 1.0 A, 2.0 A or 5.0 A.
• Secondary power auxiliary outputs.
• Wire sizes: 10 AWG (5.26 mm²) to 22 AWG (0.326 mm²).
• Battery fuse (F2): 15 A, fast-acting.
Ada masalah dengan produk ini?
ULASAN PEMBELI
Belum ada ulasan untuk produk ini
Beli produk ini dan jadilah yang pertama memberikan ulasan