5.0/ 5.0
100% pembeli merasa puas
32 rating • 6 ulasan
5(32)100%
4(0)0%
3(0)0%
2(0)0%
1(0)0%
FC ESC Stack
Atur jumlah dan catatan
Stok: Habis
Subtotal
-
SpeedyBee F405 Mini BLS 35A 3-6S 20x20mm Stack Flight Controller FC ESC for FPV Drones DJI Vista Link Air Unit O3 - FC ESC Stack
Rp939.000
Pilih warna: FC ESC Stack
Stok varian ini habis. Simpan di Wishlist untuk diingatkan ketika barang kembali tersedia.
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: Flight Controller
Specifications:
Product Name: SpeedyBee F405 Mini BLS 35A 20x20 Stack
Flight Controller: SpeedyBee F405 Min
ESC: SpeedyBee BLS 35A Mini V2 4-in-1 ESC
Bluetooth: Supported.
WiFi: NOT Supported
Wireless FC Firmware Flashing: NOT Supported
Wireless Blackbox Dwonload & Analysis: NOT Supported
Power Input: 3-6S LiPo
Mounting: 20 x 20mm 3.5mm hole size，Compatible with M2 and M3 screws/Silicone grommets
Dimension: 32mm(L) x 35mm(W) x 14.2mm(H)
Weight: 13.5g
Specifications
ProductName: SpeedyBee F405 Mini Flight Controller
MCU: STM32F405
IMU(Gyro): ICM42688P
USB Port Type: Type-C
Barometer: Built-in
OSD Chip: AT7456E chip
BLE Bluetooth: Supported.
Wireless FC Firmware Flashing: NOT Supported.
Wireless Blackbox Dwonload & Analysis: NOT Supported.
WIFI: Not supported
DJI Air Unit Connection Way: Direct soldering
DJI Air Unit Compatibility: Compatible with all DJI Air Units: DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1.
Blackbox: 8MB Onboard Flash
BetaFlight Camera Control Pad: Yes(CC pad on the front side)
Current Sensor Input: Supported. For SpeedyBee BLS 35A V2 ESC, please set Scale=250 and Offset=-500.
Power Input: 3-6S LiPo.
5V Output: 4 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side. The total current load is 2A.
9V Output: 1 group of 9V output, one +9V pad on front side. The total current load is 3A.
3.3V Output: Supported. Soldering pad named ‘3V3’ on the front top of the flight controller. Designed for 3.3V input receivers. Up to 500mA current load.
4.5V Output: Supported. Designed for radio receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC Signal: M1 - M4 wires or soldering pads on bottom side.
UART: 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6
ESC Telemetry: UART R5(UART5)
I2C: Supported. DA & CL pads on front side. Used for magnetometer, sonar, etc
Traditional Betaflight LED Pad: Supported.
Buzzer: BZ+ and BZ- pad used for 5V Buzzer
BOOT Button: Supported.
RSSI Input: Not Supported
Smart Port / F.Port: Not Supported
Supported Flight Controller Firmware: BetaFlight(Default), INAV
Firmware Target Name: SPEEDYBEEF405MINI
Mounting: 20 x 20mm 3.5mm hole diameter ，Compatible with M2 and M3 screws/Silicone grommets.
Dimension: 30(L) x 32(W) x 7.8(H)mm
Weight: 9.6g
ProductName: SpeedyBee 35A BLHeli_S Mini V2 4-in-1 ESC
Firmware: BLHeli_S J-H-40
Continuous Current: 35A * 4
Burst Current: 45A(5seconds)
ESC Protocol: DSHOT300/600
Power Input: 3-6S LiPo
Power Output: VBAT(Battery voltage, used to power the flight controller)
Current Sensor: Support (Scale=250 Offset=-500)
Mounting: 20x20mm ∅3.5mm hole size，compatible with M2 and M3 screws/Silicone grommets.
Dimension: 35x35x5.5mm
Weight: 7.2g
Product Name: SpeedyBee F405 Mini BLS 35A 20x20 Stack
Flight Controller: SpeedyBee F405 Min
ESC: SpeedyBee BLS 35A Mini V2 4-in-1 ESC
Bluetooth: Supported.
WiFi: NOT Supported
Wireless FC Firmware Flashing: NOT Supported
Wireless Blackbox Dwonload & Analysis: NOT Supported
Power Input: 3-6S LiPo
Mounting: 20 x 20mm 3.5mm hole size，Compatible with M2 and M3 screws/Silicone grommets
Dimension: 32mm(L) x 35mm(W) x 14.2mm(H)
Weight: 13.5g
Specifications
ProductName: SpeedyBee F405 Mini Flight Controller
MCU: STM32F405
IMU(Gyro): ICM42688P
USB Port Type: Type-C
Barometer: Built-in
OSD Chip: AT7456E chip
BLE Bluetooth: Supported.
Wireless FC Firmware Flashing: NOT Supported.
Wireless Blackbox Dwonload & Analysis: NOT Supported.
WIFI: Not supported
DJI Air Unit Connection Way: Direct soldering
DJI Air Unit Compatibility: Compatible with all DJI Air Units: DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1.
Blackbox: 8MB Onboard Flash
BetaFlight Camera Control Pad: Yes(CC pad on the front side)
Current Sensor Input: Supported. For SpeedyBee BLS 35A V2 ESC, please set Scale=250 and Offset=-500.
Power Input: 3-6S LiPo.
5V Output: 4 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side. The total current load is 2A.
9V Output: 1 group of 9V output, one +9V pad on front side. The total current load is 3A.
3.3V Output: Supported. Soldering pad named ‘3V3’ on the front top of the flight controller. Designed for 3.3V input receivers. Up to 500mA current load.
4.5V Output: Supported. Designed for radio receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC Signal: M1 - M4 wires or soldering pads on bottom side.
UART: 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6
ESC Telemetry: UART R5(UART5)
I2C: Supported. DA & CL pads on front side. Used for magnetometer, sonar, etc
Traditional Betaflight LED Pad: Supported.
Buzzer: BZ+ and BZ- pad used for 5V Buzzer
BOOT Button: Supported.
RSSI Input: Not Supported
Smart Port / F.Port: Not Supported
Supported Flight Controller Firmware: BetaFlight(Default), INAV
Firmware Target Name: SPEEDYBEEF405MINI
Mounting: 20 x 20mm 3.5mm hole diameter ，Compatible with M2 and M3 screws/Silicone grommets.
Dimension: 30(L) x 32(W) x 7.8(H)mm
Weight: 9.6g
ProductName: SpeedyBee 35A BLHeli_S Mini V2 4-in-1 ESC
Firmware: BLHeli_S J-H-40
Continuous Current: 35A * 4
Burst Current: 45A(5seconds)
ESC Protocol: DSHOT300/600
Power Input: 3-6S LiPo
Power Output: VBAT(Battery voltage, used to power the flight controller)
Current Sensor: Support (Scale=250 Offset=-500)
Mounting: 20x20mm ∅3.5mm hole size，compatible with M2 and M3 screws/Silicone grommets.
Dimension: 35x35x5.5mm
Weight: 7.2g
Ada masalah dengan produk ini?