5.0/ 5.0
100% pembeli merasa puas
50 rating • 16 ulasan
5(50)100%
4(0)0%
3(0)0%
2(0)0%
1(0)0%
Atur jumlah dan catatan
Stok: Habis
Subtotal
-
SpeedyBee F7 V3 BL32 50A 3-6S 30x30mm Stack Flight Controller FC ESC for FPV Drones DJI Vista Link Air Unit O3 - ESC
Rp855.000
Pilih warna: ESC
Stok varian ini habis. Simpan di Wishlist untuk diingatkan ketika barang kembali tersedia.
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: Flight Controller
Product Name: SpeedyBee F7 V3 Flight Controller
MCU: STM32F722
IMU(Gyro): BMI270
USB Port Type: Type-C
Barometer: BMP280
OSD Chip: AT7456E chip
BLE Bluetooth: Supported. Used for Flight Controller configuration,built-in a single 2.4 GHz Wi-Fi-and-Bluetooth combo chip
Flash FC Firmware Wirelessly: Supported. Please enter MENU > FC Firmware Flasher
Download/Analyze Blackbox: Supported.Please enter MENU > Blackbox Analyzer
DJI Air Unit Connection Way: Two ways supported: 6-pin connector or direct soldering.
6-pin DJI Air Unit Plug: Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
Flash(for BlackBox): 500MB
BetaFlight Camera Control Pad: Yes(CC pad on the front side)
Power Input: 3S - 6S Lipo
5V Output: 10 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 6 +5V output included in the connectors on bottom side. The total current load is 2A.
9V Output: 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 4A.
3.3V Output: Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
4.5V Output: Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC Signal Pads: M1 - M4 on bottom side and M5-M8 on front side.
UART: 5 sets(UART1, UART2, UART3, UART4(For ESC Telemetry), UART6)
ESC Telemetry UART: R4(UART4)
I2C: Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
LED Pad: Used for WS2812 LED controlled by Betaflight firmware.
Buzzer: BZ+ and BZ- pad used for 5V Buzzer
BOOT Button: Supported.
RSSI Input: Supported. Named as RS on the front side.
SmartPort: Supported
Supported Flight Controller Firmware: BetaFlight(Default),INAV
Firmware Target Name: SPEEDYBEEF7V3
Mounting: 30.5 x 30.5mm( 4mm hole diameter)
Dimension: 41(L) x 38(W) x 8.1(H)mm
Weight: 10.7g
Product Name: SpeedyBee BL32 50A 4-in-1 ESC
Firmware: SpeedyBee BL32 50A
Configurator Download Link: http://github.com/bitdump/BLHeli/releases
Continuous Current: 50A * 4
Burst Current: 55A(5seconds)
TVS Protective diode: Yes
Heat Sink: Yes
External Capacitor: 1000uF Low ESR Capacitor(In the package)
ESC Protocol: DSHOT300/600
PWM Frequency Range: 16KHz-128KHz
Power Input: 3-6S LiPo
Power Output: VBAT
Current Sensor: Support (Scale=490 Offset=0)
ESC Telemetry: supported
Mounting: 30.5 x 30.5mm( 4mm hole diameter)
Dimension: 45.6(L) * 40(W) * 8.8mm(H)
Weight: 19.2g with heat sink
MCU: STM32F722
IMU(Gyro): BMI270
USB Port Type: Type-C
Barometer: BMP280
OSD Chip: AT7456E chip
BLE Bluetooth: Supported. Used for Flight Controller configuration,built-in a single 2.4 GHz Wi-Fi-and-Bluetooth combo chip
Flash FC Firmware Wirelessly: Supported. Please enter MENU > FC Firmware Flasher
Download/Analyze Blackbox: Supported.Please enter MENU > Blackbox Analyzer
DJI Air Unit Connection Way: Two ways supported: 6-pin connector or direct soldering.
6-pin DJI Air Unit Plug: Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
Flash(for BlackBox): 500MB
BetaFlight Camera Control Pad: Yes(CC pad on the front side)
Power Input: 3S - 6S Lipo
5V Output: 10 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 6 +5V output included in the connectors on bottom side. The total current load is 2A.
9V Output: 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 4A.
3.3V Output: Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
4.5V Output: Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC Signal Pads: M1 - M4 on bottom side and M5-M8 on front side.
UART: 5 sets(UART1, UART2, UART3, UART4(For ESC Telemetry), UART6)
ESC Telemetry UART: R4(UART4)
I2C: Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
LED Pad: Used for WS2812 LED controlled by Betaflight firmware.
Buzzer: BZ+ and BZ- pad used for 5V Buzzer
BOOT Button: Supported.
RSSI Input: Supported. Named as RS on the front side.
SmartPort: Supported
Supported Flight Controller Firmware: BetaFlight(Default),INAV
Firmware Target Name: SPEEDYBEEF7V3
Mounting: 30.5 x 30.5mm( 4mm hole diameter)
Dimension: 41(L) x 38(W) x 8.1(H)mm
Weight: 10.7g
Product Name: SpeedyBee BL32 50A 4-in-1 ESC
Firmware: SpeedyBee BL32 50A
Configurator Download Link: http://github.com/bitdump/BLHeli/releases
Continuous Current: 50A * 4
Burst Current: 55A(5seconds)
TVS Protective diode: Yes
Heat Sink: Yes
External Capacitor: 1000uF Low ESR Capacitor(In the package)
ESC Protocol: DSHOT300/600
PWM Frequency Range: 16KHz-128KHz
Power Input: 3-6S LiPo
Power Output: VBAT
Current Sensor: Support (Scale=490 Offset=0)
ESC Telemetry: supported
Mounting: 30.5 x 30.5mm( 4mm hole diameter)
Dimension: 45.6(L) * 40(W) * 8.8mm(H)
Weight: 19.2g with heat sink
Ada masalah dengan produk ini?