Atur jumlah dan catatan
Stok Total: 500
Subtotal
Rp749.084
TMC2209 V1.2 Stepper Motor Driver Heatsink 2.8A Peak Driver for SKR V1.3 MKS GEN L Ramps 1.4/1.5/1.6 3D Printer Control Board
Rp749.084
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: Semua Etalase
Brand Name : AOKIN
Model Number : 3D Printer TMC2209 V1.2 Stepper Motor Driver with Heatsink
Origin : Mainland China
Item Type : MOTOR
Product description
Specification:
Power VoltageVM4.75V---28V DC
Peak Current2.8A
Current RMS2A
Microstep Setting24816can be divided into 256 parts
Max microstep256
Operating ModeSTEP/DIR or UART
The TMC2209 is an ultra-quiet two-phase stepper motor driver chip with a continuous drive current of 2A and a peak current of 2.8A.
Compared to the TMC2208, the drive current is improved by 0.6A--0.8A, while the Blockage increases the stall detection function.
Provides up to 256 segments;stallguard4TM stall detection, which can feed back an abnormal signal when the motor rotates abnormally.
Note:
Always disconnect the power supply before installing the drive to prevent the drive from burning.
Be sure to confirm the direction of the drive before installing the drive to prevent the drive from being burnt due to reverse connection.
Do not plug or unplug the drive module with power to avoid damage.
When installing the heat sink, pay attention to the contact between the heat sink and the pin header.Stop drive short circuit.
The product is sensitive to static electricity, please handle it carefully when using, it is best to move it again when using.
Must be used to heat the drive before use (heat sink, cooling fan).
Package Included:
4 X TMC2209 V1.2 stepper motor driver
4 X Jumper cable
Product description
Specification:
Power VoltageVM4.75V---28V DC
Peak Current2.8A
Current RMS2A
Microstep Setting24816can be divided into 256 parts
Max microstep256
Operating ModeSTEP/DIR or UART
The TMC2209 is an ultra-quiet two-phase stepper motor driver chip with a continuous drive current of 2A and a peak current of 2.8A.
Compared to the TMC2208, the drive current is improved by 0.6A--0.8A, while the Blockage increases the stall detection function.
Provides up to 256 segments;stallguard4TM stall detection, which can feed back an abnormal signal when the motor rotates abnormally.
Note:
Always disconnect the power supply before installing the drive to prevent the drive from burning.
Be sure to confirm the direction of the drive before installing the drive to prevent the drive from being burnt due to reverse connection.
Do not plug or unplug the drive module with power to avoid damage.
When installing the heat sink, pay attention to the contact between the heat sink and the pin header.Stop drive short circuit.
The product is sensitive to static electricity, please handle it carefully when using, it is best to move it again when using.
Must be used to heat the drive before use (heat sink, cooling fan).
Package Included:
4 X TMC2209 V1.2 stepper motor driver
4 X Jumper cable
Model Number : 3D Printer TMC2209 V1.2 Stepper Motor Driver with Heatsink
Origin : Mainland China
Item Type : MOTOR
Product description
Specification:
Power VoltageVM4.75V---28V DC
Peak Current2.8A
Current RMS2A
Microstep Setting24816can be divided into 256 parts
Max microstep256
Operating ModeSTEP/DIR or UART
The TMC2209 is an ultra-quiet two-phase stepper motor driver chip with a continuous drive current of 2A and a peak current of 2.8A.
Compared to the TMC2208, the drive current is improved by 0.6A--0.8A, while the Blockage increases the stall detection function.
Provides up to 256 segments;stallguard4TM stall detection, which can feed back an abnormal signal when the motor rotates abnormally.
Note:
Always disconnect the power supply before installing the drive to prevent the drive from burning.
Be sure to confirm the direction of the drive before installing the drive to prevent the drive from being burnt due to reverse connection.
Do not plug or unplug the drive module with power to avoid damage.
When installing the heat sink, pay attention to the contact between the heat sink and the pin header.Stop drive short circuit.
The product is sensitive to static electricity, please handle it carefully when using, it is best to move it again when using.
Must be used to heat the drive before use (heat sink, cooling fan).
Package Included:
4 X TMC2209 V1.2 stepper motor driver
4 X Jumper cable
Product description
Specification:
Power VoltageVM4.75V---28V DC
Peak Current2.8A
Current RMS2A
Microstep Setting24816can be divided into 256 parts
Max microstep256
Operating ModeSTEP/DIR or UART
The TMC2209 is an ultra-quiet two-phase stepper motor driver chip with a continuous drive current of 2A and a peak current of 2.8A.
Compared to the TMC2208, the drive current is improved by 0.6A--0.8A, while the Blockage increases the stall detection function.
Provides up to 256 segments;stallguard4TM stall detection, which can feed back an abnormal signal when the motor rotates abnormally.
Note:
Always disconnect the power supply before installing the drive to prevent the drive from burning.
Be sure to confirm the direction of the drive before installing the drive to prevent the drive from being burnt due to reverse connection.
Do not plug or unplug the drive module with power to avoid damage.
When installing the heat sink, pay attention to the contact between the heat sink and the pin header.Stop drive short circuit.
The product is sensitive to static electricity, please handle it carefully when using, it is best to move it again when using.
Must be used to heat the drive before use (heat sink, cooling fan).
Package Included:
4 X TMC2209 V1.2 stepper motor driver
4 X Jumper cable
Ada masalah dengan produk ini?
ULASAN PEMBELI
Belum ada ulasan untuk produk ini
Beli produk ini dan jadilah yang pertama memberikan ulasan