5.0/ 5.0
100% pembeli merasa puas
7 rating • 2 ulasan
5(7)100%
4(0)0%
3(0)0%
2(0)0%
1(0)0%
Atur jumlah dan catatan
Stok Total: 99991
Subtotal
Rp325.000
12V 24V 48V DC motor speed controller MACH3 PWM spindle control AP59
Rp325.000
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: CNC Control Board Dan stepper motor
12V 24V 48V DC motor speed controller MACH3 PWM spindle control AP59
Description:
1. The power input, supports only DC input. There are reverse power protection. Supply voltage range: DC: 12-50V.
2. By setting, the motor can support a variety of parameters. Adjust OC-ADJ-T match potentiometer. The maximum current is 20A .. matching can generally coarse, the factory is located at 2A.
3. When the manual independent motor control, can be controlled by PWM motor base frequency jumper settings to match different motor noise at different speeds to a minimum. There are three fundamental frequency shift, the position shown in the figure, jump cap to short left two pins is 2.1KHZ, short-circuiting two right feet are 2.9KHZ, 3 feet are not short-circuit is 11.1KHZ. When the ship is in default 2.9KHZ.
4. There are two control modes: controlled by jumper switch is manually controlled independent motor or external PWM signal or access control card PLC to control the motor. External PWM input requirements: level 3.5-12V VPP, frequency 1K-5KHZ ,. duty ratio of 0% -93%.
5. Has the alarm output function (this function available in the market are not a lot of speed). When motor stall, you can send signals to the control card or PLC, control card or PLC do let down, and other related actions.
6. Has the power light, stall / overcurrent warning indicator functions.
7. The independent can manually adjust the potentiometer on the governor to control the motor speed control motor.
8. Enter the interface specification. The internal resistance of 330 ohm resistor when connected PLC. To a 1.5-2.7K ohm resistor in series. Then MACH3 and other 5V level motion control card directly wired to.
9. Alarm output interface specification: Maximum drive current 12MA as MACH3 interface cards:. NPN-E port access GND.NPN-C port access P10 (or other inputs can also be)
10. super power control. Maximum 20A, recommends no more than 15A current.
Description:
1. The power input, supports only DC input. There are reverse power protection. Supply voltage range: DC: 12-50V.
2. By setting, the motor can support a variety of parameters. Adjust OC-ADJ-T match potentiometer. The maximum current is 20A .. matching can generally coarse, the factory is located at 2A.
3. When the manual independent motor control, can be controlled by PWM motor base frequency jumper settings to match different motor noise at different speeds to a minimum. There are three fundamental frequency shift, the position shown in the figure, jump cap to short left two pins is 2.1KHZ, short-circuiting two right feet are 2.9KHZ, 3 feet are not short-circuit is 11.1KHZ. When the ship is in default 2.9KHZ.
4. There are two control modes: controlled by jumper switch is manually controlled independent motor or external PWM signal or access control card PLC to control the motor. External PWM input requirements: level 3.5-12V VPP, frequency 1K-5KHZ ,. duty ratio of 0% -93%.
5. Has the alarm output function (this function available in the market are not a lot of speed). When motor stall, you can send signals to the control card or PLC, control card or PLC do let down, and other related actions.
6. Has the power light, stall / overcurrent warning indicator functions.
7. The independent can manually adjust the potentiometer on the governor to control the motor speed control motor.
8. Enter the interface specification. The internal resistance of 330 ohm resistor when connected PLC. To a 1.5-2.7K ohm resistor in series. Then MACH3 and other 5V level motion control card directly wired to.
9. Alarm output interface specification: Maximum drive current 12MA as MACH3 interface cards:. NPN-E port access GND.NPN-C port access P10 (or other inputs can also be)
10. super power control. Maximum 20A, recommends no more than 15A current.
Ada masalah dengan produk ini?