5.0/ 5.0
100% pembeli merasa puas
8 rating • 1 ulasan
5(8)100%
4(0)0%
3(0)0%
2(0)0%
1(0)0%
Atur jumlah dan catatan
Stok Total: 96
Subtotal
Rp650.000
Matek GNSS & COMPASS M10Q 5883 GPS GLONASS Galileo BeiDou M10 Q Module
Rp650.000
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: Semua Etalase
M10-588 has been discontinued. Replaced with M10Q-5883
M10Q-5883 uses multi-constellation GNSS module powered by u-blox SAM-M10Q-00B.
The SAM-M10Q features the u-blox M10 standard precision GNSS platform and provides exceptional sensitivity and acquisition time for all L1 GNSS signals. SAM-M10Q supports concurrent reception of four GNSS (GPS, GLONASS, Galileo, and BeiDou). The high number of visible satellites enables the receiver to select the best signals. This maximizes the position availability, in particular under challenging conditions such as in deep urban canyons. u-blox Super-S (Super-Signal) technology offers great RF sensitivity and can improve the dynamic position accuracy in non-line-of-sight scenarios.
The high-gain 15 x 15 mm2 patch antenna provides the best balance between performance and small size. The omnidirectional antenna radiation pattern increases flexibility for device installation.
More details about the SAM-M10Q, pls check out u-blox SAM-M10Q page
Specifications
GNSS u-blox SAM-M10Q-00B (GPS, GLONASS, Galileo and BeiDou)
Magnetic Compass QMC5883L
Patch antenna 15*15*4mm
Input voltage range: 4~9V (5V pad/pin)
Power consumption: 13mA
UART baudrate: 9600 default
Operating Temperatures: -20~80 °C
UART(TX, RX) interface for GNSS SAM-M10Q-00B
I2C(DA, CL) interface for Compass QMC5883L
JST-GH-6P connector (SM06B-GHS-TB). 1.27mm pitch
GNSS PPS LED, Green. (Solid ON after powering on, blinking(1Hz) when GNSS get 3D fix)
Protocol: UBX(u-blox) 5Hz@GPS+GAL+BDS B1C+GLO or NMEA 1Hz
20mm*20mm*12.4mm
8g
M10Q-5883_step.zip
Includes
1x M10Q-5883
1x JST-GH-6P to JST-GH-6P 20cm silicon wire
Wiring and settings
M10Q-5883 5V to Flight controller 4~9V
M10Q-5883 RX to Flight controller UART_TX
M10Q-5883 TX to Flight controller UART_RX
M10Q-5883 CL to Flight controller I2C_SCL
M10Q-5883 DA to Flight controller I2C_SDA
M10Q-5883 G to Flight controller GND
M10Q-5883 uses multi-constellation GNSS module powered by u-blox SAM-M10Q-00B.
The SAM-M10Q features the u-blox M10 standard precision GNSS platform and provides exceptional sensitivity and acquisition time for all L1 GNSS signals. SAM-M10Q supports concurrent reception of four GNSS (GPS, GLONASS, Galileo, and BeiDou). The high number of visible satellites enables the receiver to select the best signals. This maximizes the position availability, in particular under challenging conditions such as in deep urban canyons. u-blox Super-S (Super-Signal) technology offers great RF sensitivity and can improve the dynamic position accuracy in non-line-of-sight scenarios.
The high-gain 15 x 15 mm2 patch antenna provides the best balance between performance and small size. The omnidirectional antenna radiation pattern increases flexibility for device installation.
More details about the SAM-M10Q, pls check out u-blox SAM-M10Q page
Specifications
GNSS u-blox SAM-M10Q-00B (GPS, GLONASS, Galileo and BeiDou)
Magnetic Compass QMC5883L
Patch antenna 15*15*4mm
Input voltage range: 4~9V (5V pad/pin)
Power consumption: 13mA
UART baudrate: 9600 default
Operating Temperatures: -20~80 °C
UART(TX, RX) interface for GNSS SAM-M10Q-00B
I2C(DA, CL) interface for Compass QMC5883L
JST-GH-6P connector (SM06B-GHS-TB). 1.27mm pitch
GNSS PPS LED, Green. (Solid ON after powering on, blinking(1Hz) when GNSS get 3D fix)
Protocol: UBX(u-blox) 5Hz@GPS+GAL+BDS B1C+GLO or NMEA 1Hz
20mm*20mm*12.4mm
8g
M10Q-5883_step.zip
Includes
1x M10Q-5883
1x JST-GH-6P to JST-GH-6P 20cm silicon wire
Wiring and settings
M10Q-5883 5V to Flight controller 4~9V
M10Q-5883 RX to Flight controller UART_TX
M10Q-5883 TX to Flight controller UART_RX
M10Q-5883 CL to Flight controller I2C_SCL
M10Q-5883 DA to Flight controller I2C_SDA
M10Q-5883 G to Flight controller GND
Ada masalah dengan produk ini?