5.0/ 5.0
100% pembeli merasa puas
3 rating • 1 ulasan
5(3)100%
4(0)0%
3(0)0%
2(0)0%
1(0)0%
Atur jumlah dan catatan
Stok Total: Sisa 4
Subtotal
Rp8.500
Sensor Gerak Radar Microwave RCWL-0516 Human Body Detection Doppler
Rp8.500
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: Semua Etalase
RCWL-0516 Microwave Radar Sensor Switch Module Body Induction 4-28V 100mA
Sensor yg menggunakan teknik Radar Doppler untuk mendeteksi keberadaan objek yg bergerak.
Teknik ini lebih bagus daripada PIR (Passive Infrared) dan Ultrasonic karena tidak terpengaruh oleh cahaya dan suhu lingkungan dan memiliki daya tembus yg lebih baik.
Banyak digunakan pada berbagai peralatan elektronik yg mendeteksi kehadiran manusia seperti
1. Pencahayaan otomatis on off
2. Alarm anti pencurian
3. dll
Product Introduction:
1. Operating Voltage:4-28V
2. Operating Current:2.8mA (typical);3mA (max)
3. Detection Distance:5-9m
4. Transmitting Power:20mW (typical);30mW (max)
5. Output Voltage:3.2-3.4V
6. Output Voltage Driving Capacity:100mA
7. Trigger Way:repeat trigger
8. Output Control Low Level:0V
9. Output Control High Level:3.3V
10.Operating Temperature:-20~80 celsius
11Storage Temperature:-40~100 celsius
Adjustment Part Introduction:
1. C-TM :
Adjust repeat trigger time,default trigger time is 2s;increasing capacitor's capacity will make repeat trigger time longer;and actual counting trigger time can operate as below :
Stick capacitor on C-TM,test 9196 3-pin frequency F,repeat trigger time T=(1/f)*32768
2. R-GN
Detection distance adjustment;connect with resistor and detection distance will become shorter;if not connect,detection distance is 7m;if connect with 1M ohm resistor,detection distance is 5m
3. R-CDS
Internal VCC parallel connect with internal 1M ohm resistor to CDS pin (that is 196 9-pin) by R-CDS ,CDS connects with photoresistor,you can close detection function at night
Pin Definition:
1. 3V3: 3V3 power output
2. GND: ground
3. OUT: control output;when detect moving objects,it will output high level
4. VIN: input voltage,4-28V
5. CDS:enable control chip,lower than 0.7V,OUT will output low level all the time
Notice:
1. The right ahead of induction side should't place any metal to block
2. The front/back side should reserve more than 1cm space
3. Module and installati
Sensor yg menggunakan teknik Radar Doppler untuk mendeteksi keberadaan objek yg bergerak.
Teknik ini lebih bagus daripada PIR (Passive Infrared) dan Ultrasonic karena tidak terpengaruh oleh cahaya dan suhu lingkungan dan memiliki daya tembus yg lebih baik.
Banyak digunakan pada berbagai peralatan elektronik yg mendeteksi kehadiran manusia seperti
1. Pencahayaan otomatis on off
2. Alarm anti pencurian
3. dll
Product Introduction:
1. Operating Voltage:4-28V
2. Operating Current:2.8mA (typical);3mA (max)
3. Detection Distance:5-9m
4. Transmitting Power:20mW (typical);30mW (max)
5. Output Voltage:3.2-3.4V
6. Output Voltage Driving Capacity:100mA
7. Trigger Way:repeat trigger
8. Output Control Low Level:0V
9. Output Control High Level:3.3V
10.Operating Temperature:-20~80 celsius
11Storage Temperature:-40~100 celsius
Adjustment Part Introduction:
1. C-TM :
Adjust repeat trigger time,default trigger time is 2s;increasing capacitor's capacity will make repeat trigger time longer;and actual counting trigger time can operate as below :
Stick capacitor on C-TM,test 9196 3-pin frequency F,repeat trigger time T=(1/f)*32768
2. R-GN
Detection distance adjustment;connect with resistor and detection distance will become shorter;if not connect,detection distance is 7m;if connect with 1M ohm resistor,detection distance is 5m
3. R-CDS
Internal VCC parallel connect with internal 1M ohm resistor to CDS pin (that is 196 9-pin) by R-CDS ,CDS connects with photoresistor,you can close detection function at night
Pin Definition:
1. 3V3: 3V3 power output
2. GND: ground
3. OUT: control output;when detect moving objects,it will output high level
4. VIN: input voltage,4-28V
5. CDS:enable control chip,lower than 0.7V,OUT will output low level all the time
Notice:
1. The right ahead of induction side should't place any metal to block
2. The front/back side should reserve more than 1cm space
3. Module and installati
Ada masalah dengan produk ini?