5.0/ 5.0
100% pembeli merasa puas
7 rating • 2 ulasan
5(7)100%
4(0)0%
3(0)0%
2(0)0%
1(0)0%
Atur jumlah dan catatan
Stok Total: 22
Subtotal
Rp14.900
MPR121 MPR-121 Capacitive Touch Sensor Controller Module I2C keyboard
Rp14.900
This is a breakout board for Freescale's MPR121QR2 The MPR121 is a capacitive touch sensor controller driven by an I2C
interface The chip can control up to twelve individual electrodes, as well as a simulated thirteenth electrode The MPR121 also features eight LED driving... pins. When these pins are not configured as electrodes, they may be used to drive LEDs.
There a four jumpers on the bottom of the board, all of which are set (closed) by default. An address jumper ties the ADD pin to ground, meaning the default I2C address of the chip will be 0x5A. If you need to change the address of the chip (by shorting ADD to a different pin), make sure you open the jumper first. Jumpers also connect SDA, SCL and the interrupt pin to 10k pull-up resistors. If you do not require the pull-up resistors you can open the jumpers by cutting the trace connecting them.
There is no regulation on the board, so the voltage supplied should be between 2.5 and 3.6VDC. The VREG pin is connected through a 0.1uF capacitor to ground, which means, unless you modify the board, you can not operate the MPR121 in low-supply voltage mode (1.71-2.75VDC)
DISCLAIMER PRODUK:
Produk ini merupakan komponen elektronik/modul pendukung, bukan produk jadi dan tidak dapat digunakan secara mandiri tanpa integrasi dengan komponen atau perangkat lain. Penggunaan produk memerlukan pemahaman dasar elektronika, termasuk pemasangan dan/atau penyolderan, sehingga disarankan digunakan oleh pengguna berpengalaman atau dengan pendampingan orang dewasa/ahli/guru.
Gambar produk hanya ilustrasi, tampilan atau warna dapat berbeda tergantung batch, namun secara fungsi tetap sesuai.
Produk ditujukan untuk edukasi, eksperimen, riset, dan pengembangan, bukan untuk penggunaan konsumsi langsung. Kerusakan akibat kesalahan pemasangan, penyolderan, atau modifikasi merupakan tanggung jawab pengguna dan tidak termasuk garansi. Pembeli dianggap memahami karakteristik produk sebelum membeli.
interface The chip can control up to twelve individual electrodes, as well as a simulated thirteenth electrode The MPR121 also features eight LED driving... pins. When these pins are not configured as electrodes, they may be used to drive LEDs.
There a four jumpers on the bottom of the board, all of which are set (closed) by default. An address jumper ties the ADD pin to ground, meaning the default I2C address of the chip will be 0x5A. If you need to change the address of the chip (by shorting ADD to a different pin), make sure you open the jumper first. Jumpers also connect SDA, SCL and the interrupt pin to 10k pull-up resistors. If you do not require the pull-up resistors you can open the jumpers by cutting the trace connecting them.
There is no regulation on the board, so the voltage supplied should be between 2.5 and 3.6VDC. The VREG pin is connected through a 0.1uF capacitor to ground, which means, unless you modify the board, you can not operate the MPR121 in low-supply voltage mode (1.71-2.75VDC)
DISCLAIMER PRODUK:
Produk ini merupakan komponen elektronik/modul pendukung, bukan produk jadi dan tidak dapat digunakan secara mandiri tanpa integrasi dengan komponen atau perangkat lain. Penggunaan produk memerlukan pemahaman dasar elektronika, termasuk pemasangan dan/atau penyolderan, sehingga disarankan digunakan oleh pengguna berpengalaman atau dengan pendampingan orang dewasa/ahli/guru.
Gambar produk hanya ilustrasi, tampilan atau warna dapat berbeda tergantung batch, namun secara fungsi tetap sesuai.
Produk ditujukan untuk edukasi, eksperimen, riset, dan pengembangan, bukan untuk penggunaan konsumsi langsung. Kerusakan akibat kesalahan pemasangan, penyolderan, atau modifikasi merupakan tanggung jawab pengguna dan tidak termasuk garansi. Pembeli dianggap memahami karakteristik produk sebelum membeli.
Ada masalah dengan produk ini?