Convoy C8+ with luminus SFT40,copper DTP board and ar-coated inside,18650 flashlight

Selamat Datang Di Toko Kami,
JIka Ada Pertanyaan Terkait Produk Jangan Ragu Chat Kami ya :)

Brand Name : CONVOY MK
Certification : none
Origin : Mainland China


Parameters:

LED: luminus SFT40 6000K 5000K 3000K

Reflector : Smooth

Battery : C8+ runs on 1pcs 18650 INR or IMR lithium battery,notice that battery is not included

Driver: Ramping FET, 4modes/12groups 5ampslinear constant current, 12groups 8amps buck constant current

Diameter of head : 44.5mm

Length : 142mm

Diameter of body :
25.2mm

Weight : 145g

1.Mode instructions:(ramping driver)

Note:

1.
The speed of half-press should be fast
flashes once per 6seconds at low voltage (3V or so),and shut down later

3.No
temperature protection management,pls pay attention to the
heat,

2.Driver instructions:(4modes)

Now we offer another driver version, which has a simple 4 modes for switching, which is very suitable for ordinary users.

modes : 0.1-30 max current output is 5000mA

Its biggest advantage is that no frequency can be seen in any mode, and there is temperature management.

It can control the flashlight
temperature not to exceed 55 degrees Celsius,

If the flashlight temperature is below 55 degrees Celsius, it will output full current. If it is above 55 degrees Celsius, it will constantly adjust the current so that the flashlight will not overheat.

3.Driver instructions:(12groups)

It has the same temperature protection function as the 4modes version.

It has 12groups ,following is the driver operation instructions.

12 groups: the switch to turn the flashlight on/off,tap the switch to select mode flashlight is turnedon,tap the switch 20 times quicklyto enter into config mode.(On a visual interface,as long as you click on an option, it means that the option is selected. The flashlight has no visual interface. It flashes to represent an option, and "tap the switch in the flashing process" means to select the option.)
Option 1(normal-flash 1 time+ buzz-flash):tap the switch to enter into sub-option to select the mode group,If the user has no operation, the config mode will enter option 2.
-------------sub-option 1.1 (normal-flash1 time) : tap the switch to select mode group 1 (0.1, 10, 100%, strobe, biking, battery-check)
-------------sub-option 1.2 (normal-flash2 times) : tap the switch to select mode group2 (0.1, 10, 100%)
-------------sub-option 1.3 (normal-flash3 times) : tap the switch to select mode group3 (100, 10, 0.1%)
-------------sub-option 1.4 (normal-flash4 times) : tap the switch to select mode group4 (1, 100%, strobe, biking, battery-check, SOS)
-------------sub-option 1.5 (normal-flash5 times) : tap the switch to select mode group5 (1, 100%)
-------------sub-option 1.6 (normal-flash6 times) : tap the switch to select mode group6 (100, 1%)
-------------sub-option 1.7 (normal-flash7 times) : tap the switch to select mode group7 (0.1, 10, strobe, biking, battery-check, SOS)
-------------sub-option 1.8 (normal-flash8 times) : tap the switch to select mode group 8(0.1, 10)
-------------sub-option 1.9 (normal-flash9 times) : tap the switch to select mode group9 (50, 1)
-------------sub-option 1.10 (normal-flash10 times) : tap the switch to select mode group10 (1, 35)
-------------sub-option 1.11 (normal-flash11 times) : tap the switch to select mode group11 (100, strobe)
-------------sub-option 1.12 (normal-flash12 times) : tap the switch to select mode group 12(100% only)
Option2(normal-flash 2 times+ buzz-flash):tap the switch to active the mode memory or inactive it,If the user has no operation,flashlight will enterinto the last mode.

battery-check instructions:
3.85V 5 flashes