Motor Drive Controller BLDC Three-phase DC Brushless Hall Motor Driver Motor Board DC6-20V 60W Motor Controller Support PLC 0-5V

SELAMAT DATANG DI TOKO KAMI

Model Number : Motor Drive Controller
Color : green
Origin : Mainland China
Certification : none
Motor Type : DC Motor
Power Supply : DC
Dropship : Support


Motor Drive Controller BLDC Three-phase DC Brushless Hall Motor Driver Motor Board DC6-20V 60W Motor Controller Support PLC 0-5V

Features:

This driver is a DC three-phase brushless Hallless control board

The motor can work normally without Hall

Mini BLDC wide voltage 5-24V 3A small size embedded brushless Hallless controller,

Speed adjustment with potentiometer on board

Support PLC 0-5V analog signal speed regulation

Special instructions for the front-end control interface:

1. DIR forward and reverse & BRAKE brake active low (ground GND)

2. The SC speed output signal only leaves the interface without technical support. If you are interested, you can use an oscilloscope to look at the waveform to find methods and rules.

3. If you need an external potentiometer to adjust the speed, please remove the original potentiometer, and use a wire to lead out a one-to-one external potentiometer. There is no requirement for the size of the potentiometer, and the resistance value is 1-100K.

The picture above shows the non-inductive (no Hall) model

Instructions for use of non-inductive models:

The non-inductive type does not need Hall, and the board comes with a speed regulating potentiometer. Connect the three phase wires of the motor and the two power wires. It can work when it is powered on, and it can be used when you send the cable.

Reminder: The baby is a product independently developed by the company, and the circuit schematic diagram is not provided, please forgive me, some key ICs on the anti-copy board have been polished, please do not take photos if you mind

Interface Description:

1. U V W phase line output connected to the motor

2. VCC GND main power supply (external DC power supply)

Product parameters:

Product name: Three-phase DC brushless Hallless driver

Model: X10 (non-inductive)

Working voltage: 6-20V (limit 5-24V)

Drive current: up to 3A

Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000RPM (14-pole motor).

Product size: length 34MM* width 27MM* height 11MM

Weight: X10 8 grams (with wire)

Features: This driver is a low-power brushless driver, and it can also be embedded in other systems. It is specially used for air pumps, water pumps, oil pumps, fans, etc. of DC three-phase brushless motors with small space and low power, and industrial control electric gadgets. Default Medium timing is not suitable for high-power motors, such as working with full load current for a long time, Jianyi adds a fan to cool it

Precautions:

1. There is no fuse for the power supply circuit on the main board, and Jianyi adds it by himself. The reverse connection of the positive and negative poles of the power supply will cause permanent damage to some chips on the board (even for 1 second).

2. There is motor blocking protection during normal operation. Please do not artificially short circuit when the module is not working normally. Once the short circuit may burn the circuit and burst the tube, please use a small current and low voltage test for the first wiring test, and the voltage Three-phase DC brushless motors with comparable current and power are used to match

3. Do not connect motors that obviously do not match the voltage, current and power of the drive module or are far away from them, so as to avoid inexplicable "nonsensical" damage

Product List:

1X Driver

1X Cable

Sebelum membeli suatu produk, Mohon dapat membaca deskripsi produk dengan cermat
Harap tanyakan stok sebelum melakukan pemesanan ya kak
Jika Anda memiliki pertanyaan, silakan hubungi kami.