5.0/ 5.0
100% pembeli merasa puas
6 rating • 2 ulasan
5(6)100%
4(0)0%
3(0)0%
2(0)0%
1(0)0%
Atur jumlah dan catatan
Stok Total: Sisa 1
Subtotal
Rp975.000
Elektroda Fitel S178A, S153A, S123C-A, S123-B, S123M4-A, S123M4-B
Rp975.000
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: Elektroda - Blade Fiber Cleaver
Product Attributes
Name: Furukawa welding machine original battery
Applicable models: S178
Discharge times:> 4800 times
Loss: <0.02dB
Brand: (Fitel)
Applicable models: (Fitel) S178A, S153A, S123C-A, S123-B, S123M4-A,S123M4-B/123M12
Special note: in the process of the replacement of the electrode tip, in case of damage, and should avoid electrode drop in the machine, the replacement of the electrode after the arc position calibration.
Replacement electrode method:
First, must confirm the welding machine in a shutdown state, take the electrode chamber protective cover and loosen the fixed electrode screw, remove the electrode; then loosen the lower electrode top wire, remove the lower electrode.
Secondly, the installation of new electrodes, the operation steps and the method of the demolition of the electrode, the operation can be. The tip of the two electrode tip is: 2.6 0.2 mm.
Finally, in the assembly process, the electrode tip can not be touched, in order to prevent damage to the electrode, and to avoid the electrode caused damage to the machine inside. After replacing the electrode, the arc position should be calibrated.
Electrode cleaning and arc calibration:
In the 1 electrode after the installation is complete, open welding machine power switch.
2 welding machine into the initial screen, press the menu button to enter the menu.
3 through the cursor to find the mobile machine maintenance, into the clean electrode, after confirmation, the machine will automatically discharge clean and aging electrode.
4. Installation must good left / right fiber, through the movement of the cursor to find the arc position, through operating the end face of the fiber and the two electrode tips keep the three-point line position, the machine will discharge test, according to the actual situation can be adjusted.
5 Finally, press the menu button, followed by.
Name: Furukawa welding machine original battery
Applicable models: S178
Discharge times:> 4800 times
Loss: <0.02dB
Brand: (Fitel)
Applicable models: (Fitel) S178A, S153A, S123C-A, S123-B, S123M4-A,S123M4-B/123M12
Special note: in the process of the replacement of the electrode tip, in case of damage, and should avoid electrode drop in the machine, the replacement of the electrode after the arc position calibration.
Replacement electrode method:
First, must confirm the welding machine in a shutdown state, take the electrode chamber protective cover and loosen the fixed electrode screw, remove the electrode; then loosen the lower electrode top wire, remove the lower electrode.
Secondly, the installation of new electrodes, the operation steps and the method of the demolition of the electrode, the operation can be. The tip of the two electrode tip is: 2.6 0.2 mm.
Finally, in the assembly process, the electrode tip can not be touched, in order to prevent damage to the electrode, and to avoid the electrode caused damage to the machine inside. After replacing the electrode, the arc position should be calibrated.
Electrode cleaning and arc calibration:
In the 1 electrode after the installation is complete, open welding machine power switch.
2 welding machine into the initial screen, press the menu button to enter the menu.
3 through the cursor to find the mobile machine maintenance, into the clean electrode, after confirmation, the machine will automatically discharge clean and aging electrode.
4. Installation must good left / right fiber, through the movement of the cursor to find the arc position, through operating the end face of the fiber and the two electrode tips keep the three-point line position, the machine will discharge test, according to the actual situation can be adjusted.
5 Finally, press the menu button, followed by.
Ada masalah dengan produk ini?