Atur jumlah dan catatan
Stok Total: 21
Subtotal
Rp127.700
ESP32 cam ov2640 WiFi Bluetooth with Camera Module Development Board
Rp127.700
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: Semua Etalase
(Ready Stock) ESP32 cam WiFi Bluetooth Camera Module Development Board esp 32 with camera Module OV2640
Note = best to connect ide arduino with cp1202 usb ttl module
https://shopee.sg/product/223700280/13935002807?smtt=0.223704556-1649376747.9
About this item
The ESP32CAM is a tiny module based on ESP32 chip and OV2640. You can even program the ESP32CAM through the ESP-IDF by installing the ESP32 Core
The ESP32CAM equips the ESP32 with everything necessary to program, run and develop on the wonderchip. Additionally, the board reserved the MPU6050,BME280 and an analog MIC.
ESP integrates WiFi, traditional bluetooth and BLE Beacon, with 2 high-performance 32-bit LX6 CPUs, 7-stage pipeline architecture, main frequency adjustment range 80MHz to 240MHz, on-chip sensor, Hall sensor, temperature sensor, etc.
Features:
Ultra-small 802.11b/g/n Wi-Fi BT/BLE SoC module
Low-power dual-core 32-bit CPU for application processors
Up to 240MHz, up to 600 DMIPS
Built-in 520 KB SRAM, external 4M PSRAM
Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
Support OV2640 and OV7670 cameras with built-in flash
Support for images WiFI upload
Support TF card
Support multiple sleep modes
Embedded Lwip and FreeRTOS
Support STA/AP/STA AP working mode
Support Smart Config/AirKiss One-click distribution network
Support for serial local upgrade and remote firmware upgrade (FOTA)
Note:
1.Please ensure that the module input power is at least 5V 2A, otherwise the image will unstable.
2.ESP32 GPIO32 pin controls camera power. When the camera is working, please pull GPIO32 low.
3.Since IO0 is connected to the camera XCLK, please leave IO0 floating when using it. Do not connect high and low level.
4.The factory has the default firmware, no additional download is available. Please handle it carefully if you need to re-burn other firmware.
Note = best to connect ide arduino with cp1202 usb ttl module
https://shopee.sg/product/223700280/13935002807?smtt=0.223704556-1649376747.9
About this item
The ESP32CAM is a tiny module based on ESP32 chip and OV2640. You can even program the ESP32CAM through the ESP-IDF by installing the ESP32 Core
The ESP32CAM equips the ESP32 with everything necessary to program, run and develop on the wonderchip. Additionally, the board reserved the MPU6050,BME280 and an analog MIC.
ESP integrates WiFi, traditional bluetooth and BLE Beacon, with 2 high-performance 32-bit LX6 CPUs, 7-stage pipeline architecture, main frequency adjustment range 80MHz to 240MHz, on-chip sensor, Hall sensor, temperature sensor, etc.
Features:
Ultra-small 802.11b/g/n Wi-Fi BT/BLE SoC module
Low-power dual-core 32-bit CPU for application processors
Up to 240MHz, up to 600 DMIPS
Built-in 520 KB SRAM, external 4M PSRAM
Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
Support OV2640 and OV7670 cameras with built-in flash
Support for images WiFI upload
Support TF card
Support multiple sleep modes
Embedded Lwip and FreeRTOS
Support STA/AP/STA AP working mode
Support Smart Config/AirKiss One-click distribution network
Support for serial local upgrade and remote firmware upgrade (FOTA)
Note:
1.Please ensure that the module input power is at least 5V 2A, otherwise the image will unstable.
2.ESP32 GPIO32 pin controls camera power. When the camera is working, please pull GPIO32 low.
3.Since IO0 is connected to the camera XCLK, please leave IO0 floating when using it. Do not connect high and low level.
4.The factory has the default firmware, no additional download is available. Please handle it carefully if you need to re-burn other firmware.
Ada masalah dengan produk ini?
ULASAN PEMBELI
Belum ada ulasan untuk produk ini
Beli produk ini dan jadilah yang pertama memberikan ulasan