5.0/ 5.0
100% pembeli merasa puas
69 rating • 17 ulasan
5(69)100%
4(0)0%
3(0)0%
2(0)0%
1(0)0%
Atur jumlah dan catatan
Stok: Habis
Subtotal
-
Matek ExpressLRS 2.4Ghz ELRS Diversity Receiver R24D Long Range RX
Rp290.000
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: Flight Controller, PDB, BEC, Other Boards
ELRS-R24-D Specifications
ESP8285, SX1280/1281IMLTRT
PA/LNA: SE2431L
Antenna connector: IPEX MHF 1
RF Frequency: 2.4GHz (2400~2480MHz)
Telemetry power: 22.5dbm~23dbm
SE2431L RX_gain: 12.5dB
Diversity (antenna-switching), default ANT2
Receiver protocol: CRSF
Input voltage: 4~9V DC @ 5V pad
Power dissipation: 40~45mA(before binding), 70~75mA(binding), 90~95mA(wifi mode)
PCB size: 21mm x 15mm
Weight: 3g w/ 2x antennas
Packing: 1x ELRS-R24-D, 2x IPEX MHF1 Antennas
Firmwares
ExpressLRS MATEK_2400_RX
Firmware update via UART or WIFI
ELRS-R24-D: enable “USE_DIVERSITY” (checked) when flashing in ExpressLRS configurator
“Any ELRS 2.4Ghz receivers can work with any ELRS 2.4Ghz TX Modules, from any manufacturer and even the DIY ones. This is as long as they have the same binding phrase and configuration options (Regulatory Domain, Performance Options and Extra Data).”
More details about ExpressLRS, pls check out ExpressLRS wiki
Wiring with FC
Receiver RX — FC UART_TX for Telemetry
Receiver TX — FC UART_RX for Control
Receiver 5V — FC 5V or 4v5
Receiver G — FC GND
Receiver protocol: Serial-based receiver – CRSF
Traditional Binding
Receivers have ExpressLRS fw V1.1.0 preloaded without BINDING_PHRASE
Power on and off your receiver three times
Make sure the LED is doing a quick double blink, which indicates the receiver is in bind mode
Use the [BIND] button on the Transmitter Lua script, which sends out a binding pulse
Receiver will switch to slow blink once it has received binding pulse.
Power off and power on receiver again. If the receiver LED switch to solid on from slow blink, it’s bound with your transmitter.
Important: If the RX firmware has a bind phrase, the RX will never enter binding mode using the above procedure. It must be flashed without a binding phrase to do traditional binding.
ESP8285, SX1280/1281IMLTRT
PA/LNA: SE2431L
Antenna connector: IPEX MHF 1
RF Frequency: 2.4GHz (2400~2480MHz)
Telemetry power: 22.5dbm~23dbm
SE2431L RX_gain: 12.5dB
Diversity (antenna-switching), default ANT2
Receiver protocol: CRSF
Input voltage: 4~9V DC @ 5V pad
Power dissipation: 40~45mA(before binding), 70~75mA(binding), 90~95mA(wifi mode)
PCB size: 21mm x 15mm
Weight: 3g w/ 2x antennas
Packing: 1x ELRS-R24-D, 2x IPEX MHF1 Antennas
Firmwares
ExpressLRS MATEK_2400_RX
Firmware update via UART or WIFI
ELRS-R24-D: enable “USE_DIVERSITY” (checked) when flashing in ExpressLRS configurator
“Any ELRS 2.4Ghz receivers can work with any ELRS 2.4Ghz TX Modules, from any manufacturer and even the DIY ones. This is as long as they have the same binding phrase and configuration options (Regulatory Domain, Performance Options and Extra Data).”
More details about ExpressLRS, pls check out ExpressLRS wiki
Wiring with FC
Receiver RX — FC UART_TX for Telemetry
Receiver TX — FC UART_RX for Control
Receiver 5V — FC 5V or 4v5
Receiver G — FC GND
Receiver protocol: Serial-based receiver – CRSF
Traditional Binding
Receivers have ExpressLRS fw V1.1.0 preloaded without BINDING_PHRASE
Power on and off your receiver three times
Make sure the LED is doing a quick double blink, which indicates the receiver is in bind mode
Use the [BIND] button on the Transmitter Lua script, which sends out a binding pulse
Receiver will switch to slow blink once it has received binding pulse.
Power off and power on receiver again. If the receiver LED switch to solid on from slow blink, it’s bound with your transmitter.
Important: If the RX firmware has a bind phrase, the RX will never enter binding mode using the above procedure. It must be flashed without a binding phrase to do traditional binding.
Ada masalah dengan produk ini?