Atur jumlah dan catatan
Stok Total: 9995
Subtotal
Rp720.500
DC6.5-50V 380W BLDC Three Phase DC Brushless Motor Controller PWM Without Hall Sensor Hall Motor Control Driver Power Supply
Rp720.500
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: Semua Etalase
"Selamat Datang"
Features:
This driver is a DC three-phase brushless Hall control board
The motor can work normally without Hall
BLDC wide voltage 6.5-50V high power 380W DC three-phase high-speed brushless sensorless controller
Added PWM signal input to support 3.3V system
PLC 0-5V analog quantity, signal input control
XI0021：
Motherboard specifications:
Product name: ZS-X11F V3
Working voltage: 5-50V (limit 60V)
Drive current: rated 16A plus air cooling 25A
Power: Rated 200W-250W, peak 300W (please leave margin for use)
Overcurrent protection: yes
Stalled rotor protection: Yes (after stalled, the current automatically decreases and runs in intervals)
Over-temperature protection: Yes (over-temperature power is halved)
Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000RPM (14-pole motor).
The limit can still reach 380W, and additional heat dissipation processing must be done.
Special instructions for external signal input:
1.0-5V input mode: Press the button to switch to 0-5V input mode, and the signal is input from the terminal block to 0-5V analog signal to control the speed. The maximum speed adjustment does not exceed 5V. The driver defaults to this mode (the potentiometer on the board is adjusted to the minimum. Remember )
2.1-4.2V input mode: Press the button to switch to 1-4.2V input mode, and the signal inputs 1-4.2V analog signal from the terminal block to control the maximum speed adjustment not exceeding 5V. This mode is mainly used with the Hall handle (automatic on-board Remember to adjust the potentiometer to the minimum)
3. PWM input mode: Press the button to switch to PWM input mode, and the signal is input from the terminal block. The PWM signal controls the speed. The amplitude is 3-5V and the frequency is 1K-10K. (Remember to adjust the potentiometer on the board to the minimum)
4. The forward and reverse brake stop ports remain active at low level, and the additional switch ports are connected
Features:
This driver is a DC three-phase brushless Hall control board
The motor can work normally without Hall
BLDC wide voltage 6.5-50V high power 380W DC three-phase high-speed brushless sensorless controller
Added PWM signal input to support 3.3V system
PLC 0-5V analog quantity, signal input control
XI0021：
Motherboard specifications:
Product name: ZS-X11F V3
Working voltage: 5-50V (limit 60V)
Drive current: rated 16A plus air cooling 25A
Power: Rated 200W-250W, peak 300W (please leave margin for use)
Overcurrent protection: yes
Stalled rotor protection: Yes (after stalled, the current automatically decreases and runs in intervals)
Over-temperature protection: Yes (over-temperature power is halved)
Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000RPM (14-pole motor).
The limit can still reach 380W, and additional heat dissipation processing must be done.
Special instructions for external signal input:
1.0-5V input mode: Press the button to switch to 0-5V input mode, and the signal is input from the terminal block to 0-5V analog signal to control the speed. The maximum speed adjustment does not exceed 5V. The driver defaults to this mode (the potentiometer on the board is adjusted to the minimum. Remember )
2.1-4.2V input mode: Press the button to switch to 1-4.2V input mode, and the signal inputs 1-4.2V analog signal from the terminal block to control the maximum speed adjustment not exceeding 5V. This mode is mainly used with the Hall handle (automatic on-board Remember to adjust the potentiometer to the minimum)
3. PWM input mode: Press the button to switch to PWM input mode, and the signal is input from the terminal block. The PWM signal controls the speed. The amplitude is 3-5V and the frequency is 1K-10K. (Remember to adjust the potentiometer on the board to the minimum)
4. The forward and reverse brake stop ports remain active at low level, and the additional switch ports are connected
Ada masalah dengan produk ini?
ULASAN PEMBELI
Belum ada ulasan untuk produk ini
Beli produk ini dan jadilah yang pertama memberikan ulasan