5.0/ 5.0
100% pembeli merasa puas
20 rating • 6 ulasan
5(19)95%
4(1)5%
3(0)0%
2(0)0%
1(0)0%
Atur jumlah dan catatan
Stok: Sisa 5
Subtotal
Rp59.000
[RTI] WeMos D1 ESP-Wroom-02 WiFi Nodemcu + Module 18650 Battery Charge - Tanpa Baterai
Rp59.000
Pilih baterai: Tanpa Baterai
[RTI] WeMos D1 ESP-Wroom-02 WiFi Nodemcu + Module 18650 Battery Charge
Tidak Termasuk Battery
Board : LOLIN(WEMOS) D1 R2 & mini
Driver USB : CP2102
ESP-WROOM-02 adalah modul Wi-Fi MCU 32-bit berdaya rendah, berdasarkan chip ESP8266. Jaringan TCP/IP, ADC 10-bit, dan antarmuka HSPI/UART/PWM/I2C/I2S semuanya tertanam dalam modul ini. Modul ini menggunakan flash SPI 2 MB yang terhubung ke HSPI, bekerja sebagai budak SDIO/SPI dengan SPI kecepatan hingga 8 Mbps.
· With nodemcu.
· 18650 charging system integration. TP5410 5V 1A LiPo Charger & Boost Converter
- 3000mah 18650 battery can make run for 17 hours or more.
· Indication LED (green means full of red means · Charging) Charge and work can be done at the same time.
· 1 switch control power supply.
· 1 SMT connector available for sleep mode · 1 additional LED programmable (with gpio16 [do])
· 0.5a charge current
1A output
· Overcharge protection
· Over discharge protection
· 10 digital pin read / write / interrupt / PWM / I2C / line support (except D0)
· 1 analog input to be careful + -.
If the battery is in the wrong direction, the charging chip will be destroyed.
Video Detail :
https://youtu.be/8ROeQqt0Ewg
Tidak Termasuk Battery
Board : LOLIN(WEMOS) D1 R2 & mini
Driver USB : CP2102
ESP-WROOM-02 adalah modul Wi-Fi MCU 32-bit berdaya rendah, berdasarkan chip ESP8266. Jaringan TCP/IP, ADC 10-bit, dan antarmuka HSPI/UART/PWM/I2C/I2S semuanya tertanam dalam modul ini. Modul ini menggunakan flash SPI 2 MB yang terhubung ke HSPI, bekerja sebagai budak SDIO/SPI dengan SPI kecepatan hingga 8 Mbps.
· With nodemcu.
· 18650 charging system integration. TP5410 5V 1A LiPo Charger & Boost Converter
- 3000mah 18650 battery can make run for 17 hours or more.
· Indication LED (green means full of red means · Charging) Charge and work can be done at the same time.
· 1 switch control power supply.
· 1 SMT connector available for sleep mode · 1 additional LED programmable (with gpio16 [do])
· 0.5a charge current
1A output
· Overcharge protection
· Over discharge protection
· 10 digital pin read / write / interrupt / PWM / I2C / line support (except D0)
· 1 analog input to be careful + -.
If the battery is in the wrong direction, the charging chip will be destroyed.
Video Detail :
https://youtu.be/8ROeQqt0Ewg
Ada masalah dengan produk ini?