DISCOUNT Pixracer PRO Autopilot Xracer PX4 Pixhawk Flight Controller M8N Set RC Quadcopter Ardupilot

Pixracer PRO Autopilot Xracer PX4 Pixhawk Flight Controller M8N Set RC Quadcopter Ardupilot


**Mohon Chat/Noted Untuk Warna Dan Type Yang Tersedia **



- Semua Barang di Kirim Dari Luar Negri

- Estimasi 14-20 Hari Sampai Alamat

- Harga sudah termasuk biaya ongkir dr China to Jakarta + Biaya Pajak

- Seller Amanah, Packing Aman dan Secure



-Terima Kasih Sudah Berbelanja & Jangan Lupa Follow Toko Kami
PIXRACER PRO


The Pixracer Pro has been designed primarily for the demanding requirements of small multicopters, but of course can be used on planes and other vehicles which require no more than 8 pwm outputs for controlling escs and motors.


Specifications
Specifications
mRo Pixracer Pro
Main Processor
32-bit STM32H743 Cortex M7 RISC core with FPU 460 MHz
IO Processor
No
RAM
1024 KB RAM
Flash
2 MB FRAM
Crypto / Hash Processor
No
Accelerometers / Gyros / Mags
Accelerometers / Gyros / Mags
Sensors – Dampened
Bosch BMI085 (6DOF) (internally vibration dampened)
Sensors
Invensense/TDK ICM-20602 (6DOF)
Invensense/TDK ICM-20948 (9DOF)
Internal Magnetometer
AK09916 inside ICM-20948
Barometer
Infineon DPS310 barometer (Very smooth and NO light sensitivity)
Interfaces and Protocols
6x UART (serial ports) [2x with HW flow control,1x FRSky Telemetry (D or X types), 2x General Purpose & 1x GPS+I2C].
1x PPM sum input signal
8x PWM outputs (all D-Shot capable)
1x RSSI (PWM or voltage) input
1x I2C
1x SPI
2x CAN
1x SWD (TC2030 Connector)
3x Ultra low-noise LDO voltage regulator
Supported RC input protocols:
Spektrum DSM / DSM2 / DSM-X Satellite compatible input and binding.
Futaba S.BUS & S.BUS2 compatible input.
FRSky Telemetry port output.
Graupner SUMD.
Yuneec ST24.
Connectors
– JST-GH
– USB-C
Pin Headers
Yes – 8 Servo
Conformal Coating
No
Extended Testing and Burn In
No
Custom Carrier Board Support
No
LED
Yes (RGB)
Dimensions
Width: 36mm (1.42”)
Length: 36mm (1.42”)
Weight
9.09g (.31 oz)
Mounting Holes
4mm holes at 31.5mm spacing, Silicone grommets for m3 screws
Protector Case
Optional
Typical Platforms
-Multirotor
-Rover
-Fixed-Wing
-Boats
-Submarines
-VTOL
-Automatic Tractors
-Others
Compatibility
PX4 >1.13.0, Ardupilot
Firmware
The mRo Pixracer Pro is compatible with the following firmware:
ArduPilot
-ArduCopter 4.x
-ArduPlane 4.x
-ArduRover 4.x
PX4
-PX4 greater than v1.13.0 (master or beta only until v1.13.1 release)
Normal Usage Guide
-> BATT_VOLT_PIN= 14
-> BATT_CURR_PIN= 15
All connectors follow the Dronecode connector standard. All connectors are JST-GH.Pixracer Pro do not have a safety switch option, If theres a need to have one a CAN switch is required.
Pinout


Specifications:
Hign-concerned Chemical: None
Is Electric: No battery
Quantity: 1 pcs
Wheelbase: Bottom Plate
Size: 35mm*35mm
Model Number: PIXRACER PRO
For Vehicle Type: Airplanes
Tool Supplies: Assembled class
Four-wheel Drive Attributes: Assemblage
Remote Control Peripherals/Devices: Remote Controller
Upgrade Parts/Accessories: Frame
Material: EVA
Brand Name: RDR
Origin: Mainland China
Recommend Age: 14+y
Use: Vehicles & Remote Control Toys
Hign-concerned Chemical: None
Is Electric: No battery
Quantity: 1 pcs
Wheelbase: Bottom Plate
Size: 35mm*35mm
Model Number: PIXRACER PRO
For Vehicle Type: Airplanes
Tool Supplies: Assembled class
Four-wheel Drive Attributes: Assemblage
Remote Control Peripherals/Devices: Remote Controller