4.9/ 5.0
100% pembeli merasa puas
18 rating • 5 ulasan
5(17)94.44%
4(1)5.56%
3(0)0%
2(0)0%
1(0)0%
TDS PROBE
Atur jumlah dan catatan
Stok: Habis
Subtotal
-
DFROBOT Analog TDS Sensor/Meter for Arduino - TDS PROBE
Rp22.500
Pilih ukuran: TDS PROBE
Stok varian ini habis. Simpan di Wishlist untuk diingatkan ketika barang kembali tersedia.
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: SENSOR
#26
This product supports 3.3 ~ 5.5V wide voltage input, and 0 ~ 2.3V analog voltage output, which makes it compatible with 5V or 3.3V control system or board.
This product can be used in water quality application, such as domestic water, hydroponics. With this product, you can easily DIY a TDS detector to reflect the cleanliness of water to protect your health.
Attention:
1.The probe can not be used in water above 55 degrees centigrade.
2.The probe can not be left too close to the edge of the container, otherwise it will affect the reading.
3.The head and the cable of the probe are waterproof, but the connector and the signal transmitter board are not waterproof. Please be careful.
FEATURES
Wide Voltage Input: 3.3~5.5V
Good Compatibility Output: 0~2.3V analog signal output, compatible with 5V or 3.3V controller
AC Excitation Source: effectively prevent probe from polarization
Waterproof Probe
Easy to Use: Arduino compatible, simple connection, plug and play without soldering
SPECIFICATION
Signal Transmitter Board
Input Voltage: 3.3 ~ 5.5V
Output Voltage: 0 ~ 2.3V
Working Current: 3 ~ 6mA
TDS Measurement Range: 0 ~ 1000ppm
TDS Measurement Accuracy: ± 10% F.S. (25 ℃)
Module Size: 42 * 32mm
Module Interface: PH2.0-3P
Electrode Interface: XH2.54-2P
TDS probe
Number of Needle: 2
Total Length: 83cm
Connection Interface: XH2.54-2P
SHIPPING LIST
Gravity: Analog TDS Sensor/Meter for Arduino x1
Waterproof TDS Probe x1
Gravity-3Pin Analog Sensor Cable x1
This product supports 3.3 ~ 5.5V wide voltage input, and 0 ~ 2.3V analog voltage output, which makes it compatible with 5V or 3.3V control system or board.
This product can be used in water quality application, such as domestic water, hydroponics. With this product, you can easily DIY a TDS detector to reflect the cleanliness of water to protect your health.
Attention:
1.The probe can not be used in water above 55 degrees centigrade.
2.The probe can not be left too close to the edge of the container, otherwise it will affect the reading.
3.The head and the cable of the probe are waterproof, but the connector and the signal transmitter board are not waterproof. Please be careful.
FEATURES
Wide Voltage Input: 3.3~5.5V
Good Compatibility Output: 0~2.3V analog signal output, compatible with 5V or 3.3V controller
AC Excitation Source: effectively prevent probe from polarization
Waterproof Probe
Easy to Use: Arduino compatible, simple connection, plug and play without soldering
SPECIFICATION
Signal Transmitter Board
Input Voltage: 3.3 ~ 5.5V
Output Voltage: 0 ~ 2.3V
Working Current: 3 ~ 6mA
TDS Measurement Range: 0 ~ 1000ppm
TDS Measurement Accuracy: ± 10% F.S. (25 ℃)
Module Size: 42 * 32mm
Module Interface: PH2.0-3P
Electrode Interface: XH2.54-2P
TDS probe
Number of Needle: 2
Total Length: 83cm
Connection Interface: XH2.54-2P
SHIPPING LIST
Gravity: Analog TDS Sensor/Meter for Arduino x1
Waterproof TDS Probe x1
Gravity-3Pin Analog Sensor Cable x1
Ada masalah dengan produk ini?