Atur jumlah dan catatan
Stok Total: 12
Subtotal
Rp720.000
Arduino MKR1000 WIFI ABX00004 - MKR 1000 Original Made In Italy
Rp720.000
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: 01 - ARDUINO OFFICIAL
𝐍𝐎𝐓𝐄: 𝐓𝐈𝐃𝐀𝐊 𝐌𝐄𝐍𝐄𝐑𝐈𝐌𝐀 𝐊𝐋𝐀𝐈𝐌 𝐀𝐓𝐀𝐔 𝐊𝐎𝐌𝐏𝐋𝐀𝐈𝐍 𝐃𝐈 𝐋𝐔𝐀𝐑 𝐒𝐈𝐒𝐓𝐄𝐌 𝐓𝐎𝐊𝐎𝐏𝐄𝐃𝐈𝐀
SKU: KL3027
Code: ABX00004
Arduino MKR1000 specification:
MICROCONTROLLER = SAMD21 Cortex-M0+ 32bit low power ARM MCU
BOARD POWER SUPPLY (USB/VIN) = 5V
SUPPORTED BATTERY(*) = Li-Po single cell, 3.7V, 700mAh minimum
CIRCUIT OPERATING VOLTAGE = 3.3V
DIGITAL I/O PINS = 8
PWM PINS = 12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19)
UART = 1
SPI = 1
I2C = 1
ANALOG INPUT PINS = 7 (ADC 8/10/12 bit)
ANALOG OUTPUT PINS = 1 (DAC 10 bit)
EXTERNAL INTERRUPTS = 8 (0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17)
DC CURRENT PER I/O PIN = 7 mA
FLASH MEMORY = 256 KB
SRAM = 32 KB
EEPROM = no
CLOCK SPEED = 32.768 kHz (RTC), 48 MHz
LED_BUILTIN = 6
FULL-SPEED USB DEVICE AND EMBEDDED HOST
LENGTH = 61.5 mm
WIDTH = 25 mm
WEIGHT = 32 gr.
The MKR1000 Wifi module supports certificate SHA-256.
Warning: Unlike most Arduino & Genuino boards, the MKR1000 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting.
SKU: KL3027
Code: ABX00004
Arduino MKR1000 specification:
MICROCONTROLLER = SAMD21 Cortex-M0+ 32bit low power ARM MCU
BOARD POWER SUPPLY (USB/VIN) = 5V
SUPPORTED BATTERY(*) = Li-Po single cell, 3.7V, 700mAh minimum
CIRCUIT OPERATING VOLTAGE = 3.3V
DIGITAL I/O PINS = 8
PWM PINS = 12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19)
UART = 1
SPI = 1
I2C = 1
ANALOG INPUT PINS = 7 (ADC 8/10/12 bit)
ANALOG OUTPUT PINS = 1 (DAC 10 bit)
EXTERNAL INTERRUPTS = 8 (0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17)
DC CURRENT PER I/O PIN = 7 mA
FLASH MEMORY = 256 KB
SRAM = 32 KB
EEPROM = no
CLOCK SPEED = 32.768 kHz (RTC), 48 MHz
LED_BUILTIN = 6
FULL-SPEED USB DEVICE AND EMBEDDED HOST
LENGTH = 61.5 mm
WIDTH = 25 mm
WEIGHT = 32 gr.
The MKR1000 Wifi module supports certificate SHA-256.
Warning: Unlike most Arduino & Genuino boards, the MKR1000 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting.
Ada masalah dengan produk ini?
ULASAN PEMBELI
Belum ada ulasan untuk produk ini
Beli produk ini dan jadilah yang pertama memberikan ulasan