5.0/ 5.0
100% pembeli merasa puas
1 rating • 1 ulasan
5(1)100%
4(0)0%
3(0)0%
2(0)0%
1(0)0%
Atur jumlah dan catatan
Stok Total: Sisa 6
Subtotal
Rp23.500.000
INCRA TS-LS Table Saw Fence 1320mm Range
Rp23.500.000
Pilih incra fence: 3 incra fence
- Kondisi: Baru
- Min. Pemesanan: 1 Buah
- Etalase: Measure Tools
INCRA TS-LS Table Saw Fence - 32"/810mm Capacity
The 32”/810mm -capacity TS-LS is based on 72” aluminum main rails and a 32”-travel LS Positioner. The standard TS-LS (LS32-TS) covers saws measuring 28" or smaller front-to-rear (measured along the miter slot). The “XL” version fits most of the newer 10” & 12” cabinet saws with deeper tops measuring 33.5” or less using a longer fence and base support panel. Choose from 1/32" imperial or 1mm metric positioning mechanics below.
INCRA TS-LS Table Saw Fence - 52"/1320mm Capacity
The 52"/1320mm -capacity TS-LS is based on 92” aluminum main rails and a 32”-travel LS Positioner. The standard TS-LS (LS52-TS) covers saws measuring 28" or smaller front-to-rear (measured along the miter slot). The “XL” version fits most of the newer 10” & 12” cabinet saws with deeper tops measuring 33.5” or less using a longer fence and base support panel. Choose from 1/32" imperial or 1mm metric positioning mechanics below.
Choose Standard or XL:
Measure your saw’s top front to rear along the miter slot. The standard TS-LS (LS52-TS) covers saws measuring 28" or smaller front-to-rear. The “XL” version uses a longer fence and base support panel to fit most of the newer 10” & 12” cabinet saws with deeper tops measuring 33.5” or less.
The saw’s left-to-right width won’t matter for systems not equipped with router tables. You’ll keep your cast iron wings installed, and your existing extension tables can be reused.
Basic requirements for ALL table saws:
The saw’s top must have flat, vertical surfaces on both the front and rear for the (4) adjustable Incra rail mounting brackets to bolt against – two brackets at the front and two on the rear. The brackets are attached with a minimum 5/16”-18 or 8mm bolt. The bolt holes need to be centered between 3/4” and 1-3/8” down from the saw’s top surface, with enough clearance underneath the saw’s top for the washers, nuts and wrench (if the holes aren’t threaded).
The General Compatibility Chart lists the various categories of saws, and the TS-LS owner's manual is the best resource for seeing how the 4 rail mounting brackets attach and comparing that to your saw.
The 32”/810mm -capacity TS-LS is based on 72” aluminum main rails and a 32”-travel LS Positioner. The standard TS-LS (LS32-TS) covers saws measuring 28" or smaller front-to-rear (measured along the miter slot). The “XL” version fits most of the newer 10” & 12” cabinet saws with deeper tops measuring 33.5” or less using a longer fence and base support panel. Choose from 1/32" imperial or 1mm metric positioning mechanics below.
INCRA TS-LS Table Saw Fence - 52"/1320mm Capacity
The 52"/1320mm -capacity TS-LS is based on 92” aluminum main rails and a 32”-travel LS Positioner. The standard TS-LS (LS52-TS) covers saws measuring 28" or smaller front-to-rear (measured along the miter slot). The “XL” version fits most of the newer 10” & 12” cabinet saws with deeper tops measuring 33.5” or less using a longer fence and base support panel. Choose from 1/32" imperial or 1mm metric positioning mechanics below.
Choose Standard or XL:
Measure your saw’s top front to rear along the miter slot. The standard TS-LS (LS52-TS) covers saws measuring 28" or smaller front-to-rear. The “XL” version uses a longer fence and base support panel to fit most of the newer 10” & 12” cabinet saws with deeper tops measuring 33.5” or less.
The saw’s left-to-right width won’t matter for systems not equipped with router tables. You’ll keep your cast iron wings installed, and your existing extension tables can be reused.
Basic requirements for ALL table saws:
The saw’s top must have flat, vertical surfaces on both the front and rear for the (4) adjustable Incra rail mounting brackets to bolt against – two brackets at the front and two on the rear. The brackets are attached with a minimum 5/16”-18 or 8mm bolt. The bolt holes need to be centered between 3/4” and 1-3/8” down from the saw’s top surface, with enough clearance underneath the saw’s top for the washers, nuts and wrench (if the holes aren’t threaded).
The General Compatibility Chart lists the various categories of saws, and the TS-LS owner's manual is the best resource for seeing how the 4 rail mounting brackets attach and comparing that to your saw.
Ada masalah dengan produk ini?